WARP Project Forums - Wireless Open-Access Research Platform

>> clear all
>> wl_setup
Setting up WARPLab Paths...
   removing path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\classes'
   removing path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\util'
   removing path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\util\inifile'
   removing path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\config'
   removing path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\mex'
   adding path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\classes'
   adding path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\util'
   adding path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\util\inifile'
   adding path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\mex'
   adding path 'F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\config'
   saving path


A wl_config.ini file was found in your path. Values specified in this
configuration file will be used as defaults in the construction of the
new file.


------------------------------------------------------------
Please enter a WARPLab Ethernet interface address.

Pressing enter without typing an input will use a default
IP address of: 10.0.0.250

WARPNet Ethernet Interface Address: 
   defaulting to 10.0.0.250


------------------------------------------------------------
Please enter a WARPLab host ID.
Valid host IDs are integers in the range of [200,254]

Pressing enter without typing an input will use a default
host ID of: 250

WARPLab Host ID: 
   defaulting to 250


------------------------------------------------------------
Please enter a unicast starting port.

Pressing enter without typing an input will use a default
unicast starting port of: 9000

Unicast Starting Port: 
   defaulting to 9000


------------------------------------------------------------
Please enter a broadcast port.

Pressing enter without typing an input will use a default
broadcast port of: 10000

Broadcast Port: 
   defaulting to 10000


------------------------------------------------------------
Select from the following available transports:
   For better transport performance, please setup the WARPLab Mex UDP transport: 
      http://warpproject.org/trac/wiki/WARPLab/MEX 
[1] (default) Java UDP
Selection: 
   setting to java


------------------------------------------------------------
Enable jumbo frame support? (experimental)
[1] (default) false
[2]           true
Selection: 
   setting to false


------------------------------------------------------------


Setup Complete
wl_ver():
WARPLab v7.4.0 

Framework Location:
F:\WARP\WARPx\Demo\warplab\WARPLab_Reference_Design_7.4.0\M_Code_Reference\
>> clear
>> N=1;nodes=wl_initNodes(N);wl_nodeCmd(nodes,'identify');disp(nodes)

Error in node 1 with ID = 0: 
ME = 

  MException with properties:

    identifier: 'wl_transport_eth_java:send:noReply'
       message: 'maximum number of retransmissions met without reply from node'
         cause: {0x1 cell}
         stack: [6x1 struct]

Error message follows:
maximum number of retransmissions met without reply from node

Error using wl_initNodes (line 162)
The following nodes with IDs = [ 0 ] are not responding. Please ensure that the nodes have been
configured with the WARPLab bitstream.