# ##############################################################################
# Created by Base System Builder Wizard for Xilinx EDK 8.2.01 Build EDK_Im_Sp1.3
# Wed Jan 24 09:12:18 2007
# Target Board:  Rice University - WARP Project WARP FPGA and Radio Boards Rev FPGA 1.2  &   Radio 1.4
# Family:	 virtex2p
# Device:	 XC2VP70
# Package:	 FF1517
# Speed Grade:	 -6
# Processor: PPC 405
# Processor clock frequency: 200.000000 MHz
# Bus clock frequency: 50.000000 MHz
# Debug interface: FPGA JTAG
# On Chip Memory : 320 KB
# ##############################################################################


 PARAMETER VERSION = 2.1.0


 PORT fpga_0_LEDs_4Bit_GPIO_d_out_pin = fpga_0_LEDs_4Bit_GPIO_d_out, DIR = O, VEC = [0:3]
 PORT fpga_0_Push_Buttons_4bit_GPIO_in_pin = fpga_0_Push_Buttons_4bit_GPIO_in, DIR = I, VEC = [0:3]
 PORT fpga_0_RS232_RX_pin = fpga_0_RS232_RX, DIR = I
 PORT fpga_0_RS232_TX_pin = fpga_0_RS232_TX, DIR = O
 PORT sys_clk_pin = dcm_clk_s, DIR = I, SIGIS = CLK, CLK_FREQ = 100000000
 PORT sys_rst_pin = sys_rst_s, DIR = I, RST_POLARITY = 1, SIGIS = RST


BEGIN ppc405
 PARAMETER INSTANCE = ppc405_0
 PARAMETER HW_VER = 2.00.c
 BUS_INTERFACE JTAGPPC = jtagppc_0_0
 BUS_INTERFACE ISOCM = iocm
 BUS_INTERFACE DSOCM = docm
 BUS_INTERFACE IPLB = plb
 BUS_INTERFACE DPLB = plb
 PORT PLBCLK = sys_clk_s
 PORT C405RSTCHIPRESETREQ = C405RSTCHIPRESETREQ
 PORT C405RSTCORERESETREQ = C405RSTCORERESETREQ
 PORT C405RSTSYSRESETREQ = C405RSTSYSRESETREQ
 PORT RSTC405RESETCHIP = RSTC405RESETCHIP
 PORT RSTC405RESETCORE = RSTC405RESETCORE
 PORT RSTC405RESETSYS = RSTC405RESETSYS
 PORT BRAMISOCMCLK = sys_clk_s
 PORT BRAMDSOCMCLK = sys_clk_s
 PORT EICC405EXTINPUTIRQ = EICC405EXTINPUTIRQ
 PORT CPMC405CLOCK = proc_clk_s
END

BEGIN ppc405
 PARAMETER INSTANCE = ppc405_1
 PARAMETER HW_VER = 2.00.c
 BUS_INTERFACE JTAGPPC = jtagppc_0_1
END

BEGIN jtagppc_cntlr
 PARAMETER INSTANCE = jtagppc_0
 PARAMETER HW_VER = 2.00.a
 BUS_INTERFACE JTAGPPC0 = jtagppc_0_0
 BUS_INTERFACE JTAGPPC1 = jtagppc_0_1
END

BEGIN proc_sys_reset
 PARAMETER INSTANCE = reset_block
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT Ext_Reset_In = sys_rst_s
 PORT Slowest_sync_clk = sys_clk_s
 PORT Chip_Reset_Req = C405RSTCHIPRESETREQ
 PORT Core_Reset_Req = C405RSTCORERESETREQ
 PORT System_Reset_Req = C405RSTSYSRESETREQ
 PORT Rstc405resetchip = RSTC405RESETCHIP
 PORT Rstc405resetcore = RSTC405RESETCORE
 PORT Rstc405resetsys = RSTC405RESETSYS
 PORT Bus_Struct_Reset = sys_bus_reset
 PORT Dcm_locked = dcm_0_lock
END

BEGIN isocm_v10
 PARAMETER INSTANCE = iocm
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_ISCNTLVALUE = 0x87
 PORT ISOCM_Clk = sys_clk_s
 PORT sys_rst = sys_bus_reset
END

BEGIN isbram_if_cntlr
 PARAMETER INSTANCE = iocm_cntlr
 PARAMETER HW_VER = 3.00.a
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0001ffff
 BUS_INTERFACE ISOCM = iocm
 BUS_INTERFACE DCR_WRITE_PORT = isocm_porta
 BUS_INTERFACE INSTRN_READ_PORT = isocm_portb
END

BEGIN bram_block
 PARAMETER INSTANCE = isocm_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = isocm_porta
 BUS_INTERFACE PORTB = isocm_portb
END

BEGIN dsocm_v10
 PARAMETER INSTANCE = docm
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_DSCNTLVALUE = 0x87
 PORT DSOCM_Clk = sys_clk_s
 PORT sys_rst = sys_bus_reset
END

BEGIN dsbram_if_cntlr
 PARAMETER INSTANCE = docm_cntlr
 PARAMETER HW_VER = 3.00.a
 PARAMETER C_BASEADDR = 0x21800000
 PARAMETER C_HIGHADDR = 0x2180ffff
 BUS_INTERFACE DSOCM = docm
 BUS_INTERFACE PORTA = dsocm_porta
END

BEGIN bram_block
 PARAMETER INSTANCE = dsocm_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = dsocm_porta
END

BEGIN plb_v34
 PARAMETER INSTANCE = plb
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_DCR_INTFCE = 0
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT SYS_Rst = sys_bus_reset
 PORT PLB_Clk = sys_clk_s
END

BEGIN opb_v20
 PARAMETER INSTANCE = opb
 PARAMETER HW_VER = 1.10.c
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT SYS_Rst = sys_bus_reset
 PORT OPB_Clk = sys_clk_s
END

BEGIN plb2opb_bridge
 PARAMETER INSTANCE = plb2opb
 PARAMETER HW_VER = 1.01.a
 PARAMETER C_DCR_INTFCE = 0
 PARAMETER C_RNG0_BASEADDR = 0x40000000
 PARAMETER C_RNG0_HIGHADDR = 0x7fffffff
 PARAMETER C_NUM_ADDR_RNG = 1
 BUS_INTERFACE SPLB = plb
 BUS_INTERFACE MOPB = opb
END

BEGIN opb_gpio
 PARAMETER INSTANCE = LEDs_4Bit
 PARAMETER HW_VER = 3.01.b
 PARAMETER C_GPIO_WIDTH = 4
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 0
 PARAMETER C_ALL_INPUTS = 0
 PARAMETER C_BASEADDR = 0x40020000
 PARAMETER C_HIGHADDR = 0x4002ffff
 BUS_INTERFACE SOPB = opb
 PORT GPIO_d_out = fpga_0_LEDs_4Bit_GPIO_d_out
END

BEGIN opb_gpio
 PARAMETER INSTANCE = Push_Buttons_4bit
 PARAMETER HW_VER = 3.01.b
 PARAMETER C_INTERRUPT_PRESENT = 1
 PARAMETER C_GPIO_WIDTH = 4
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 0
 PARAMETER C_ALL_INPUTS = 1
 PARAMETER C_BASEADDR = 0x40000000
 PARAMETER C_HIGHADDR = 0x4000ffff
 BUS_INTERFACE SOPB = opb
 PORT IP2INTC_Irpt = Push_Buttons_4bit_IP2INTC_Irpt
 PORT GPIO_in = fpga_0_Push_Buttons_4bit_GPIO_in
END

BEGIN opb_uartlite
 PARAMETER INSTANCE = RS232
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BAUDRATE = 57600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_ODD_PARITY = 0
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_CLK_FREQ = 50000000
 PARAMETER C_BASEADDR = 0x40600000
 PARAMETER C_HIGHADDR = 0x4060ffff
 BUS_INTERFACE SOPB = opb
 PORT RX = fpga_0_RS232_RX
 PORT TX = fpga_0_RS232_TX
END

BEGIN plb_bram_if_cntlr
 PARAMETER INSTANCE = plb_bram_if_cntlr_1
 PARAMETER HW_VER = 1.00.b
 PARAMETER c_plb_clk_period_ps = 20000
 PARAMETER c_baseaddr = 0xfffe0000
 PARAMETER c_highaddr = 0xffffffff
 BUS_INTERFACE SPLB = plb
 BUS_INTERFACE PORTA = plb_bram_if_cntlr_1_port
END

BEGIN bram_block
 PARAMETER INSTANCE = plb_bram_if_cntlr_1_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = plb_bram_if_cntlr_1_port
END

BEGIN opb_intc
 PARAMETER INSTANCE = opb_intc_0
 PARAMETER HW_VER = 1.00.c
 PARAMETER C_BASEADDR = 0x41200000
 PARAMETER C_HIGHADDR = 0x4120ffff
 BUS_INTERFACE SOPB = opb
 PORT Irq = EICC405EXTINPUTIRQ
 PORT Intr = Push_Buttons_4bit_IP2INTC_Irpt&opb_timer_0_Interrupt
END

BEGIN dcm_module
 PARAMETER INSTANCE = dcm_0
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_CLK0_BUF = TRUE
 PARAMETER C_CLK2X_BUF = TRUE
 PARAMETER C_CLKDV_BUF = TRUE
 PARAMETER C_CLKDV_DIVIDE = 2.000000
 PARAMETER C_CLKIN_PERIOD = 10.000000
 PARAMETER C_CLK_FEEDBACK = 1X
 PARAMETER C_DLL_FREQUENCY_MODE = LOW
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT CLKIN = dcm_clk_s
 PORT CLK2X = proc_clk_s
 PORT CLKDV = sys_clk_s
 PORT CLK0 = dcm_0_FB
 PORT CLKFB = dcm_0_FB
 PORT RST = net_gnd
 PORT LOCKED = dcm_0_lock
END

BEGIN opb_timer
 PARAMETER INSTANCE = opb_timer_0
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BASEADDR = 0x41c00000
 PARAMETER C_HIGHADDR = 0x41c0ffff
 BUS_INTERFACE SOPB = opb
 PORT Interrupt = opb_timer_0_Interrupt
END