# ##############################################################################
# Mango 802.11 Reference Design
# XPS Hardware Specification (system.mhs)
# Copyright 2018 Mango Communications
# Distributed under the Mango Research License:
# http://mangocomm.com/802.11/license
# ##############################################################################
 PARAMETER VERSION = 2.1.0


# ##############################################################################
# Top Level Ports
# ##############################################################################
 PORT reset_pb = reset_pb, DIR = I, SIGIS = RST, RST_POLARITY = 1
# USERIO
 PORT userio_pb_d = userio_pb_d, DIR = I
 PORT userio_pb_m = userio_pb_m, DIR = I
 PORT userio_pb_u = userio_pb_u, DIR = I
 PORT userio_leds_green = userio_leds_green, DIR = O, VEC = [3:0]
 PORT userio_leds_red = userio_leds_red, DIR = O, VEC = [3:0]
# PORT userio_dipsw = userio_dipsw, DIR = I, VEC = [0:3]
 PORT userio_dipsw = userio_dipsw_b0 & userio_dipsw_b1 & userio_dipsw_b2 & userio_dipsw_b3, DIR = I, VEC = [0:3]
 PORT userio_hexdisp_left = userio_hexdisp_left, DIR = O, VEC = [6:0]
 PORT userio_hexdisp_right = userio_hexdisp_right, DIR = O, VEC = [6:0]
 PORT userio_hexdisp_left_dp = userio_hexdisp_left_dp, DIR = O
 PORT userio_hexdisp_right_dp = userio_hexdisp_right_dp, DIR = O
 PORT userio_rfa_led_red = userio_rfa_led_red, DIR = O
 PORT userio_rfa_led_green = userio_rfa_led_green, DIR = O
 PORT userio_rfb_led_red = userio_rfb_led_red, DIR = O
 PORT userio_rfb_led_green = userio_rfb_led_green, DIR = O
# Ethernet pins
 PORT ETH_COMA = net_gnd, DIR = O
# ETH_A
 PORT ETH_A_PHY_RST_N = ETH_A_PHY_RST_N, DIR = O
 PORT ETH_A_MDIO = ETH_A_MDIO, DIR = IO
 PORT ETH_A_MDC = ETH_A_MDC, DIR = O
 PORT ETH_A_RGMII_TXC = ETH_A_RGMII_TXC, DIR = O
 PORT ETH_A_RGMII_TX_CTL = ETH_A_RGMII_TX_CTL, DIR = O
 PORT ETH_A_RGMII_TXD = ETH_A_RGMII_TXD, DIR = O, VEC = [3:0]
 PORT ETH_A_RGMII_RXC = ETH_A_RGMII_RXC, DIR = I
 PORT ETH_A_RGMII_RX_CTL = ETH_A_RGMII_RX_CTL, DIR = I
 PORT ETH_A_RGMII_RXD = ETH_A_RGMII_RXD, DIR = I, VEC = [3:0]
 PORT ETH_A_PD = net_gnd, DIR = O
# ETH_B
 PORT ETH_B_MDIO = ETH_B_MDIO, DIR = IO
 PORT ETH_B_MDC = ETH_B_MDC, DIR = O
 PORT ETH_B_RGMII_TXC = ETH_B_RGMII_TXC, DIR = O
 PORT ETH_B_RGMII_TX_CTL = ETH_B_RGMII_TX_CTL, DIR = O
 PORT ETH_B_RGMII_TXD = ETH_B_RGMII_TXD, DIR = O, VEC = [3:0]
 PORT ETH_B_RGMII_RXC = ETH_B_RGMII_RXC, DIR = I
 PORT ETH_B_RGMII_RX_CTL = ETH_B_RGMII_RX_CTL, DIR = I
 PORT ETH_B_RGMII_RXD = ETH_B_RGMII_RXD, DIR = I, VEC = [3:0]
 PORT ETH_B_PD = net_gnd, DIR = O
# USB UART
 PORT usb_uart_rx = usb_uart_rx, DIR = I
 PORT usb_uart_tx = usb_uart_tx, DIR = O
# AD9512 clock buffer control pins (RF reference & sampling clocks)
 PORT clk_rfref_spi_cs_n = clk_rfref_spi_cs_n, DIR = O
 PORT clk_rfref_spi_mosi = clk_rfref_spi_mosi, DIR = O
 PORT clk_rfref_spi_sclk = clk_rfref_spi_sclk, DIR = O
 PORT clk_rfref_spi_miso = clk_rfref_spi_miso, DIR = I
 PORT clk_rfref_func = net_vcc, DIR = O
 PORT clk_samp_spi_cs_n = clk_samp_spi_cs_n, DIR = O
 PORT clk_samp_spi_mosi = clk_samp_spi_mosi, DIR = O
 PORT clk_samp_spi_sclk = clk_samp_spi_sclk, DIR = O
 PORT clk_samp_spi_miso = clk_samp_spi_miso, DIR = I
 PORT clk_samp_func = net_vcc, DIR = O
# CM-PLL pins
 PORT cm_spi_sclk = cm_spi_sclk, DIR = O
 PORT cm_spi_mosi = cm_spi_mosi, DIR = O
 PORT cm_spi_miso = cm_spi_miso, DIR = I
 PORT cm_spi_cs_n = cm_spi_cs_n, DIR = O
 PORT cm_pll_status = cm_pll_status, DIR = I
 PORT cm_switch = cm_switch, DIR = I, VEC = [2:0]
 PORT pll_refclk_p = pll_refclk, DIR = I, DIFFERENTIAL_POLARITY = P, SIGIS = CLK, CLK_FREQ = 80000000
 PORT pll_refclk_n = pll_refclk, DIR = I, DIFFERENTIAL_POLARITY = N, SIGIS = CLK, CLK_FREQ = 80000000
# IIC EEPROM pins on-board
 PORT iic_eeprom_onboard_scl = iic_eeprom_onboard_scl, DIR = IO
 PORT iic_eeprom_onboard_sda = iic_eeprom_onboard_sda, DIR = IO
# 80MHz sampling clock from AD9512
 PORT samp_clk_p = ad_refclk_in, DIR = I, DIFFERENTIAL_POLARITY = P, SIGIS = CLK, CLK_FREQ = 80000000
 PORT samp_clk_n = ad_refclk_in, DIR = I, DIFFERENTIAL_POLARITY = N, SIGIS = CLK, CLK_FREQ = 80000000
# 200MHz LVDS oscillator input
 PORT osc200_p = osc200_in, DIR = I, DIFFERENTIAL_POLARITY = P, SIGIS = CLK, CLK_FREQ = 200000000
 PORT osc200_n = osc200_in, DIR = I, DIFFERENTIAL_POLARITY = N, SIGIS = CLK, CLK_FREQ = 200000000
# AD9963 ADC/DAC control pins (RFA & RFB)
 PORT RFA_AD_spi_cs_n = RFA_AD_spi_cs_n, DIR = O
 PORT RFA_AD_spi_sdio = RFA_AD_spi_sdio, DIR = IO
 PORT RFA_AD_spi_sclk = RFA_AD_spi_sclk, DIR = O
 PORT RFA_AD_reset_n = RFA_AD_reset_n, DIR = O
 PORT RFB_AD_spi_cs_n = RFB_AD_spi_cs_n, DIR = O
 PORT RFB_AD_spi_sdio = RFB_AD_spi_sdio, DIR = IO
 PORT RFB_AD_spi_sclk = RFB_AD_spi_sclk, DIR = O
 PORT RFB_AD_reset_n = RFB_AD_reset_n, DIR = O
# RFA AD pins
 PORT RFA_AD_TRXD = rfa_trxd, DIR = I, VEC = [11:0]
 PORT RFA_AD_TRXCLK = rfa_trxclk, DIR = I
 PORT RFA_AD_TRXIQ = rfa_trxiq, DIR = I
 PORT RFA_AD_TXD = rfa_txd, DIR = O, VEC = [11:0]
 PORT RFA_AD_TXIQ = rfa_txiq, DIR = O
 PORT RFA_AD_TXCLK = rfa_txclk, DIR = O
# RFB AD pins
 PORT RFB_AD_TRXD = rfb_trxd, DIR = I, VEC = [11:0]
 PORT RFB_AD_TRXCLK = rfb_trxclk, DIR = I
 PORT RFB_AD_TRXIQ = rfb_trxiq, DIR = I
 PORT RFB_AD_TXD = rfb_txd, DIR = O, VEC = [11:0]
 PORT RFB_AD_TXIQ = rfb_txiq, DIR = O
 PORT RFB_AD_TXCLK = rfb_txclk, DIR = O
# RSSI ADC pins
 PORT RFA_RSSI_D = RFA_RSSI_D, DIR = I, VEC = [9:0]
 PORT RFB_RSSI_D = RFB_RSSI_D, DIR = I, VEC = [9:0]
 PORT RF_RSSI_CLK = wlan_rssi_clk, DIR = O
 PORT RF_RSSI_PD = net_gnd, DIR = O
# RFA transceiver and front-end
 PORT RFA_TxEn = RFA_TxEn, DIR = O
 PORT RFA_RxEn = RFA_RxEn, DIR = O
 PORT RFA_RxHP = RFA_RxHP, DIR = O
 PORT RFA_SHDN = RFA_SHDN, DIR = O
 PORT RFA_SPI_SCLK = RFA_SPI_SCLK, DIR = O
 PORT RFA_SPI_MOSI = RFA_SPI_MOSI, DIR = O
 PORT RFA_SPI_CSn = RFA_SPI_CSn, DIR = O
 PORT RFA_B = RFA_B, DIR = O, VEC = [0:6]
 PORT RFA_LD = RFA_LD, DIR = I
 PORT RFA_PAEn_24 = RFA_PAEn_24, DIR = O
 PORT RFA_PAEn_5 = RFA_PAEn_5, DIR = O
 PORT RFA_AntSw = RFA_AntSw, DIR = O, VEC = [0:1]
# RFB transceiver and front-end
 PORT RFB_TxEn = RFB_TxEn, DIR = O
 PORT RFB_RxEn = RFB_RxEn, DIR = O
 PORT RFB_RxHP = RFB_RxHP, DIR = O
 PORT RFB_SHDN = RFB_SHDN, DIR = O
 PORT RFB_SPI_SCLK = RFB_SPI_SCLK, DIR = O
 PORT RFB_SPI_MOSI = RFB_SPI_MOSI, DIR = O
 PORT RFB_SPI_CSn = RFB_SPI_CSn, DIR = O
 PORT RFB_B = RFB_B, DIR = O, VEC = [0:6]
 PORT RFB_LD = RFB_LD, DIR = I
 PORT RFB_PAEn_24 = RFB_PAEn_24, DIR = O
 PORT RFB_PAEn_5 = RFB_PAEn_5, DIR = O
 PORT RFB_AntSw = RFB_AntSw, DIR = O, VEC = [0:1]
# DDR3 SODIMM
 PORT ddr3_sodimm_ck_p = ddr3_sodimm_ck_p, DIR = O, SIGIS = CLK, VEC = [1:0]
 PORT ddr3_sodimm_ck_n = ddr3_sodimm_ck_n, DIR = O, SIGIS = CLK, VEC = [1:0]
 PORT ddr3_sodimm_cke = ddr3_sodimm_cke, DIR = O
 PORT ddr3_sodimm_cs_n = ddr3_sodimm_cs_n, DIR = O
 PORT ddr3_sodimm_odt = ddr3_sodimm_odt, DIR = O
 PORT ddr3_sodimm_ras_n = ddr3_sodimm_ras_n, DIR = O
 PORT ddr3_sodimm_cas_n = ddr3_sodimm_cas_n, DIR = O
 PORT ddr3_sodimm_we_n = ddr3_sodimm_we_n, DIR = O
 PORT ddr3_sodimm_ba = ddr3_sodimm_ba, DIR = O, VEC = [2:0]
 PORT ddr3_sodimm_addr = ddr3_sodimm_addr, DIR = O, VEC = [14:0]
 PORT ddr3_sodimm_dq = ddr3_sodimm_dq, DIR = IO, VEC = [63:0]
 PORT ddr3_sodimm_dm = ddr3_sodimm_dm, DIR = O, VEC = [7:0]
 PORT ddr3_sodimm_reset_n = ddr3_sodimm_reset_n, DIR = O
 PORT ddr3_sodimm_dqs_p = ddr3_sodimm_dqs_p, DIR = IO, VEC = [7:0]
 PORT ddr3_sodimm_dqs_n = ddr3_sodimm_dqs_n, DIR = IO, VEC = [7:0]
# Debug pins (connected through w3_userio core)
 PORT dbg_hdr = dbg_hdr, DIR = IO, VEC = [15:0]


# ##############################################################################
# WLAN Sysgen Peripherals
# ##############################################################################
BEGIN wlan_phy_tx_pmd_axiw
 PARAMETER INSTANCE = wlan_phy_tx
 PARAMETER HW_VER = 4.01.a
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_BASEADDR = 0x40000000
 PARAMETER C_HIGHADDR = 0x4000FFFF
 BUS_INTERFACE PORTB = WLAN_TX_PKT_BUF_PORTB
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT axi_aclk = clk_160MHz
 PORT sysgen_clk = clk_160MHz
 PORT samp_ce = RF_AD_samp_ce
 PORT rfa_dac_i = RFA_TX_I
 PORT rfa_dac_q = RFA_TX_Q
 PORT rfb_dac_i = RFB_TX_I
 PORT rfb_dac_q = RFB_TX_Q
 PORT rx_sigs_invalid = rx_sigs_invalid
# RC -> PHY start
 PORT RC_PHY_START = tx_phy_start
# PHY -> RC state ctrl
 PORT rc_usr_rxen = rc_usr_rxen
 PORT rc_usr_txen_a = phy_rc_txen_a
 PORT rc_usr_txen_b = phy_rc_txen_b
 PORT rc_tx_gain_a = phy_rc_tx_gain_a
 PORT rc_tx_gain_b = phy_rc_tx_gain_b
# MAC <-> Tx PHY ports
 PORT phy_tx_gain_a = mac_phy_tx_gain_a
 PORT phy_tx_gain_b = mac_phy_tx_gain_b
 PORT phy_tx_pkt_buf = mac_phy_tx_pkt_buf
 PORT phy_tx_phy_mode = mac_phy_tx_phy_mode
 PORT phy_tx_start = mac_phy_tx_start
 PORT phy_tx_done = mac_phy_tx_done
 PORT phy_tx_started = mac_phy_tx_started
 PORT phy_tx_ant_mask = mac_phy_tx_ant_mask
# Debug ports
 PORT dbg_tx_running = dbg_tx_running
END

BEGIN wlan_phy_rx_pmd_axiw
 PARAMETER INSTANCE = wlan_phy_rx
 PARAMETER HW_VER = 4.01.z
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_BASEADDR = 0x41000000
 PARAMETER C_HIGHADDR = 0x4100FFFF
 BUS_INTERFACE PORTB = WLAN_RX_PKT_BUF_PORTB
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT axi_aclk = clk_160MHz
 PORT sysgen_clk = clk_160MHz
# PORT pkt_det_in = net_wlan_phy_rx_pkt_det_in
 PORT pkt_det_in = net_gnd
 PORT rx_sigs_invalid = rx_sigs_invalid
 PORT rx_iq_samp_ce = agc_iq_valid_out
 PORT rfa_rx_i = agc_rfa_i
 PORT rfa_rx_q = agc_rfa_q
 PORT rfa_rssi = RFA_RSSI_D_REG
 PORT rfb_rx_i = agc_rfb_i
 PORT rfb_rx_q = agc_rfb_q
 PORT rfb_rssi = RFB_RSSI_D_REG
 PORT rssi_adc_clk = wlan_rssi_clk
 PORT pkt_det_o = phy_rx_pkt_det
 PORT rfa_g_rf = agc_rfa_g_rf
 PORT rfa_g_bb = agc_rfa_g_bb
 PORT rfb_g_rf = agc_rfb_g_rf
 PORT rfb_g_bb = agc_rfb_g_bb
 PORT agc_done = agc_done
# MAC <-> PHY ports
 PORT phy_rx_reset = phy_rx_reset
 PORT phy_rx_block_pktdet = phy_rx_block_pktdet
 PORT phy_cca_ind_busy = mac_phy_cca_ind_busy
 PORT phy_rx_data_byte = mac_phy_rx_data_byte
 PORT phy_rx_data_bytenum = mac_phy_rx_data_bytenum
 PORT phy_rx_data_done_ind = mac_phy_rx_data_done_ind
 PORT phy_rx_data_ind = mac_phy_rx_data_ind
 PORT phy_rx_end_ind = mac_phy_rx_end_ind
 PORT phy_rx_end_rxerror = mac_phy_rx_end_rxerror
 PORT phy_rx_fcs_good_ind = mac_phy_rx_fcs_good_ind
 PORT phy_rx_phy_hdr_ind = mac_phy_rx_phy_hdr_ind
 PORT phy_rx_phy_hdr_length = mac_phy_rx_phy_hdr_length
 PORT phy_rx_phy_hdr_mcs = mac_phy_rx_phy_hdr_mcs
 PORT phy_rx_phy_hdr_phy_mode = mac_phy_rx_phy_hdr_phy_mode
 PORT phy_rx_phy_hdr_unsupported = mac_phy_rx_phy_hdr_unsupported
 PORT phy_rx_start_ind = mac_phy_rx_start_ind
 PORT phy_rx_start_phy_sel = phy_rx_start_phy_sel
# Debug ports
 PORT dbg_dsss_rx_active = dbg_dsss_rx_active
 PORT dbg_lts_timeout = dbg_lts_timeout
 PORT dbg_pkt_det_dsss = dbg_pkt_det_dsss
 PORT dbg_pkt_det_ofdm = dbg_pkt_det_ofdm
 PORT dbg_payload = dbg_ofdm_rx_active
 PORT dbg_rssi_det = dbg_rssi_det
 PORT dbg_signal_err_disp = dbg_signal_err_disp
END

BEGIN wlan_mac_hw_axiw
 PARAMETER INSTANCE = wlan_mac_hw
 PARAMETER HW_VER = 2.01.m
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_BASEADDR = 0x42000000
 PARAMETER C_HIGHADDR = 0x4200FFFF
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT axi_aclk = clk_160MHz
 PORT sysgen_clk = clk_160MHz
 PORT phy_cca_ind_busy = mac_phy_cca_ind_busy
 PORT phy_rx_data_byte = mac_phy_rx_data_byte
 PORT phy_rx_data_bytenum = mac_phy_rx_data_bytenum
 PORT phy_rx_data_done_ind = mac_phy_rx_data_done_ind
 PORT phy_rx_data_ind = mac_phy_rx_data_ind
 PORT phy_rx_end_ind = mac_phy_rx_end_ind
 PORT phy_rx_end_rxerror = mac_phy_rx_end_rxerror
 PORT phy_rx_fcs_good_ind = mac_phy_rx_fcs_good_ind
 PORT phy_rx_start_ind = mac_phy_rx_start_ind
 PORT phy_rx_start_phy_sel = phy_rx_start_phy_sel
 PORT phy_rx_reset = phy_rx_reset
 PORT phy_rx_phy_hdr_ind = mac_phy_rx_phy_hdr_ind
 PORT phy_rx_phy_hdr_length = mac_phy_rx_phy_hdr_length
 PORT phy_rx_phy_hdr_mcs = mac_phy_rx_phy_hdr_mcs
 PORT phy_rx_phy_hdr_phy_mode = mac_phy_rx_phy_hdr_phy_mode
 PORT phy_rx_phy_hdr_unsupported = mac_phy_rx_phy_hdr_unsupported
 PORT phy_tx_done = mac_phy_tx_done
 PORT phy_tx_started = mac_phy_tx_started
 PORT phy_tx_pkt_buf = mac_phy_tx_pkt_buf
 PORT phy_tx_phy_mode = mac_phy_tx_phy_mode
 PORT phy_tx_start = mac_phy_tx_start
 PORT phy_tx_gain_a = mac_phy_tx_gain_a
 PORT phy_tx_gain_b = mac_phy_tx_gain_b
 PORT phy_tx_ant_mask = mac_phy_tx_ant_mask
 PORT phy_rx_block_pktdet = phy_rx_block_pktdet
 PORT mac_time_usec_lsb = mac_time_usec_lsb
 PORT mac_time_usec_msb = mac_time_usec_msb
 PORT mac_time_usec_frac = mac_time_usec_frac
 PORT force_cca_busy = net_gnd
 PORT force_start_postrx_timer1 = net_gnd
 PORT aux_mac_hw_status0 = net_gnd
 PORT aux_mac_hw_status1 = net_gnd
 PORT aux_mac_hw_status2 = net_gnd
 PORT aux_mac_hw_status3 = net_gnd
# # Debug outputs - can be routed to debug header
 PORT dbg_backoff_a_active = dbg_mac_backoff_a_active
 PORT dbg_backoff_c_active = dbg_mac_backoff_c_active
 PORT dbg_eifs_sel = dbg_mac_eifs_sel
 PORT dbg_idle_for_difs = dbg_mac_idle_for_difs
 PORT dbg_nav_active = dbg_mac_nav_active
 PORT dbg_tx_a_pending = dbg_mac_tx_a_pending
 PORT dbg_tx_b_pending = dbg_mac_tx_b_pending
 PORT dbg_tx_c_pending = dbg_mac_tx_c_pending
 PORT dbg_tx_d_pending = dbg_mac_tx_d_pending
END

BEGIN wlan_agc_axiw
 PARAMETER INSTANCE = wlan_agc
 PARAMETER HW_VER = 2.00.d
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_BASEADDR = 0x43000000
 PARAMETER C_HIGHADDR = 0x4300FFFF
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT axi_aclk = clk_160MHz
 PORT sysgen_clk = clk_160MHz
 PORT agc_run = phy_rx_pkt_det
 PORT agc_done = agc_done
# IQ Inputs from radio
 PORT adc_iq_valid = RF_AD_samp_ce
 PORT rfa_rssi = RFA_RSSI_D_REG
 PORT rfa_rx_i_in = RFA_RX_I
 PORT rfa_rx_q_in = RFA_RX_Q
 PORT rfb_rssi = RFB_RSSI_D_REG
 PORT rfb_rx_i_in = RFB_RX_I
 PORT rfb_rx_q_in = RFB_RX_Q
# DCO-corrected IQ outputs
 PORT iq_valid_out = agc_iq_valid_out
 PORT rfa_rx_i_out = agc_rfa_i
 PORT rfa_rx_q_out = agc_rfa_q
 PORT rfb_rx_i_out = agc_rfb_i
 PORT rfb_rx_q_out = agc_rfb_q
# Gain outputs
 PORT rfa_agc_g_bb = agc_rfa_g_bb
 PORT rfa_agc_g_rf = agc_rfa_g_rf
 PORT rfa_agc_rxhp = agc_rfa_rxhp
 PORT rfb_agc_g_bb = agc_rfb_g_bb
 PORT rfb_agc_g_rf = agc_rfb_g_rf
 PORT rfb_agc_rxhp = agc_rfb_rxhp
END

# ##############################################################################
# Radio Control Logic
# ##############################################################################
BEGIN w3_clock_controller_axi
 PARAMETER INSTANCE = w3_clock_controller
 PARAMETER HW_VER = 4.00.a
 PARAMETER C_DPHASE_TIMEOUT = 0
 PARAMETER C_BASEADDR = 0x22100000
 PARAMETER C_HIGHADDR = 0x2210FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT samp_spi_cs_n = clk_samp_spi_cs_n
 PORT samp_spi_mosi = clk_samp_spi_mosi
 PORT samp_spi_miso = clk_samp_spi_miso
 PORT samp_spi_sclk = clk_samp_spi_sclk
 PORT samp_func = samp_func
 PORT rfref_spi_cs_n = clk_rfref_spi_cs_n
 PORT rfref_spi_mosi = clk_rfref_spi_mosi
 PORT rfref_spi_miso = clk_rfref_spi_miso
 PORT rfref_spi_sclk = clk_rfref_spi_sclk
 PORT rfref_func = rfref_func
 PORT cm_spi_cs_n = cm_spi_cs_n
 PORT cm_spi_mosi = cm_spi_mosi
 PORT cm_spi_miso = cm_spi_miso
 PORT cm_spi_sclk = cm_spi_sclk
 PORT cm_pll_status = cm_pll_status
 PORT pll_refclk = pll_refclk
 PORT usr_status = net_gnd
 PORT at_boot_clk_in = clk_200MHz
 PORT at_boot_clk_in_valid = clk_gen_async_clks_locked
 PORT at_boot_config_sw = cm_switch
 PORT at_boot_clkbuf_clocks_invalid = mmcm_inputs_invalid
# Communication ports
 PORT uart_tx = clk_cfg_uart_tx
 PORT iic_eeprom_scl_I = clk_cfg_iic_eeprom_scl_I
 PORT iic_eeprom_scl_T = clk_cfg_iic_eeprom_scl_T
 PORT iic_eeprom_scl_O = clk_cfg_iic_eeprom_scl_O
 PORT iic_eeprom_sda_I = clk_cfg_iic_eeprom_sda_I
 PORT iic_eeprom_sda_T = clk_cfg_iic_eeprom_sda_T
 PORT iic_eeprom_sda_O = clk_cfg_iic_eeprom_sda_O
END

BEGIN w3_ad_controller_axi
 PARAMETER INSTANCE = w3_ad_controller
 PARAMETER HW_VER = 3.02.a
 PARAMETER C_BASEADDR = 0x22200000
 PARAMETER C_HIGHADDR = 0x2220FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER INCLUDE_RFC_RFD_IO = 0
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT RF_AD_TXCLK_out_en = RF_AD_TXCLK_out_en
 PORT RFA_AD_spi_cs_n = RFA_AD_spi_cs_n
 PORT RFA_AD_spi_sdio = RFA_AD_spi_sdio
 PORT RFA_AD_spi_sclk = RFA_AD_spi_sclk
 PORT RFA_AD_reset_n = RFA_AD_reset_n
 PORT RFB_AD_spi_cs_n = RFB_AD_spi_cs_n
 PORT RFB_AD_spi_sdio = RFB_AD_spi_sdio
 PORT RFB_AD_spi_sclk = RFB_AD_spi_sclk
 PORT RFB_AD_reset_n = RFB_AD_reset_n
END

BEGIN w3_ad_bridge
 PARAMETER INSTANCE = ad_bridge_onBoard
 PARAMETER HW_VER = 3.03.b
# Clock ports (inputs to w3_ad_bridge)
 PORT sys_clk = clk_160MHz
 PORT samp_ce = RF_AD_samp_ce
 PORT ad_TXCLK_out_en = RF_AD_TXCLK_out_en
# Top-level AD9963 ports
 PORT ad_RFA_TXD = rfa_txd
 PORT ad_RFA_TXCLK = rfa_txclk
 PORT ad_RFA_TXIQ = rfa_txiq
 PORT ad_RFA_TRXD = rfa_trxd
 PORT ad_RFA_TRXCLK = rfa_trxclk
 PORT ad_RFA_TRXIQ = rfa_trxiq
 PORT ad_RFB_TXD = rfb_txd
 PORT ad_RFB_TXCLK = rfb_txclk
 PORT ad_RFB_TXIQ = rfb_txiq
 PORT ad_RFB_TRXD = rfb_trxd
 PORT ad_RFB_TRXCLK = rfb_trxclk
 PORT ad_RFB_TRXIQ = rfb_trxiq
 PORT user_RFA_TXD_I = RFA_TX_I
 PORT user_RFA_TXD_Q = RFA_TX_Q
 PORT user_RFA_RXD_I = RFA_RX_I
 PORT user_RFA_RXD_Q = RFA_RX_Q
 PORT user_RFB_TXD_I = RFB_TX_I
 PORT user_RFB_TXD_Q = RFB_TX_Q
 PORT user_RFB_RXD_I = RFB_RX_I
 PORT user_RFB_RXD_Q = RFB_RX_Q
END

BEGIN radio_controller_axi
 PARAMETER INSTANCE = radio_controller
 PARAMETER HW_VER = 3.01.a
 PARAMETER C_BASEADDR = 0x22300000
 PARAMETER C_HIGHADDR = 0x2230FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT RFA_TxEn = RFA_TxEn
 PORT RFA_RxEn = RFA_RxEn
 PORT RFA_RxHP = RFA_RxHP
 PORT RFA_SHDN = RFA_SHDN
 PORT RFA_SPI_SCLK = RFA_SPI_SCLK
 PORT RFA_SPI_MOSI = RFA_SPI_MOSI
 PORT RFA_SPI_CSn = RFA_SPI_CSn
 PORT RFA_B = RFA_B
 PORT RFA_LD = RFA_LD
 PORT RFA_PAEn_24 = RFA_PAEn_24
 PORT RFA_PAEn_5 = RFA_PAEn_5
 PORT RFA_AntSw = RFA_AntSw
 PORT RFB_TxEn = RFB_TxEn
 PORT RFB_RxEn = RFB_RxEn
 PORT RFB_RxHP = RFB_RxHP
 PORT RFB_SHDN = RFB_SHDN
 PORT RFB_SPI_SCLK = RFB_SPI_SCLK
 PORT RFB_SPI_MOSI = RFB_SPI_MOSI
 PORT RFB_SPI_CSn = RFB_SPI_CSn
 PORT RFB_B = RFB_B
 PORT RFB_LD = RFB_LD
 PORT RFB_PAEn_24 = RFB_PAEn_24
 PORT RFB_PAEn_5 = RFB_PAEn_5
 PORT RFB_AntSw = RFB_AntSw
 PORT usr_RFA_statLED_Tx = RFA_statLED_Tx
 PORT usr_RFA_statLED_Rx = RFA_statLED_Rx
 PORT usr_RFB_statLED_Tx = RFB_statLED_Tx
 PORT usr_RFB_statLED_Rx = RFB_statLED_Rx
# Inter-core ports for hardware radio control
 PORT usr_any_PHYStart = tx_phy_start
 PORT usr_RFA_TxEn = phy_rc_txen_a
 PORT usr_RFA_RxEn = rc_usr_rxen
 PORT usr_RFA_RxHP = agc_rfa_rxhp
 PORT usr_RFA_RxGainBB = agc_rfa_g_bb
 PORT usr_RFA_RxGainRF = agc_rfa_g_rf
 PORT usr_RFA_TxGain = phy_rc_tx_gain_a
 PORT usr_RFB_TxEn = phy_rc_txen_b
 PORT usr_RFB_RxEn = rc_usr_rxen
 PORT usr_RFB_RxHP = agc_rfb_rxhp
 PORT usr_RFB_RxGainBB = agc_rfb_g_bb
 PORT usr_RFB_RxGainRF = agc_rfb_g_rf
 PORT usr_RFB_TxGain = phy_rc_tx_gain_b
END

# ##############################################################################
# Clocks and Reset
# ##############################################################################
BEGIN proc_sys_reset
 PARAMETER INSTANCE = sys_reset
 PARAMETER HW_VER = 3.00.a
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT MB_Debug_Sys_Rst = sys_reset_debug_rst
 PORT Dcm_locked = clk_gen_all_locked
 PORT MB_Reset = sys_reset_MB_Reset
 PORT Slowest_sync_clk = clk_80MHz
 PORT Interconnect_aresetn = sys_reset_Interconnect_aresetn
 PORT Ext_Reset_In = reset_pb
 PORT BUS_STRUCT_RESET = sys_reset_BUS_STRUCT_RESET
END

BEGIN clock_generator
 PARAMETER INSTANCE = clock_generator_dram_clocks
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER HW_VER = 4.03.a
# 80MHz clock input (driven by other clock generator)
 PARAMETER C_CLKIN_FREQ = 80000000
# MIG DRAM clock (2x bus)
 PARAMETER C_CLKOUT0_FREQ = 320000000
 PARAMETER C_CLKOUT0_PHASE = 0
 PARAMETER C_CLKOUT0_GROUP = MMCM0
 PARAMETER C_CLKOUT0_BUF = TRUE
# MIG DRAM clock (2x bus, variable phase)
 PARAMETER C_CLKOUT1_FREQ = 320000000
 PARAMETER C_CLKOUT1_PHASE = 0
 PARAMETER C_CLKOUT1_GROUP = MMCM0
 PARAMETER C_CLKOUT1_BUF = FALSE
 PARAMETER C_CLKOUT1_VARIABLE_PHASE = TRUE
 PARAMETER C_PSDONE_GROUP = MMCM0
 PORT CLKIN = clk_80MHz
 PORT PSCLK = clk_80MHz
 PORT RST = mmcm_inputs_invalid
 PORT LOCKED = clk_gen_dram_clks_locked
 PORT CLKOUT0 = clk_dram_320MHz_clk_mem
 PORT CLKOUT1 = clk_dram_320MHz_clk_rd_base
 PORT PSEN = MMCM_PSEN
 PORT PSINCDEC = MMCM_PSINCDEC
 PORT PSDONE = MMCM_PSDONE
END

BEGIN clock_generator
 PARAMETER INSTANCE = clk_gen_proc_bus_clks
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER HW_VER = 4.03.a
# 80MHz clock input (driven by AD9512 for sampling clock)
 PARAMETER C_CLKIN_FREQ = 80000000
# MB and primary bus
 PARAMETER C_CLKOUT0_FREQ = 80000000
 PARAMETER C_CLKOUT0_PHASE = 0
 PARAMETER C_CLKOUT0_GROUP = MMCM0
 PARAMETER C_CLKOUT0_BUF = TRUE
# MB and primary bus
 PARAMETER C_CLKOUT1_FREQ = 160000000
 PARAMETER C_CLKOUT1_PHASE = 0
 PARAMETER C_CLKOUT1_GROUP = MMCM0
 PARAMETER C_CLKOUT1_BUF = TRUE
 PORT CLKIN = ad_refclk_in
 PORT CLKOUT0 = clk_80MHz
 PORT CLKOUT1 = clk_160MHz
 PORT RST = mmcm_inputs_invalid
 PORT LOCKED = clk_gen_proc_bus_clks_locked
END

BEGIN clock_generator
 PARAMETER INSTANCE = clk_gen_async_clks
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER HW_VER = 4.03.a
# 200MHz clock input (driven by 200MHz LVDS oscillator)
 PARAMETER C_CLKIN_FREQ = 200000000
# TEMAC TxClk
 PARAMETER C_CLKOUT0_FREQ = 125000000
 PARAMETER C_CLKOUT0_PHASE = 0
 PARAMETER C_CLKOUT0_GROUP = NONE
 PARAMETER C_CLKOUT0_BUF = TRUE
# IDELAYCTRL refclk
 PARAMETER C_CLKOUT1_FREQ = 200000000
 PARAMETER C_CLKOUT1_PHASE = 0
 PARAMETER C_CLKOUT1_GROUP = NONE
 PARAMETER C_CLKOUT1_BUF = TRUE
 PORT CLKIN = osc200_in
 PORT CLKOUT0 = clk_125MHz
 PORT CLKOUT1 = clk_200MHz
 PORT RST = reset_pb
 PORT LOCKED = clk_gen_async_clks_locked
END

# ##############################################################################
# Shared Cores
# ##############################################################################
BEGIN axi_interconnect
 PARAMETER INSTANCE = mb_shared_axi
 PARAMETER HW_VER = 1.06.a
 PORT INTERCONNECT_ACLK = clk_160MHz
 PORT INTERCONNECT_ARESETN = sys_reset_Interconnect_aresetn
END

BEGIN mailbox
 PARAMETER INSTANCE = mb_mailbox
 PARAMETER HW_VER = 1.01.b
 PARAMETER C_INTERCONNECT_PORT_0 = 2
 PARAMETER C_INTERCONNECT_PORT_1 = 2
 PARAMETER C_IMPL_STYLE = 1
 PARAMETER C_MAILBOX_DEPTH = 512
 PARAMETER C_S0_AXI_BASEADDR = 0x30000000
 PARAMETER C_S0_AXI_HIGHADDR = 0x3000FFFF
 PARAMETER C_S1_AXI_BASEADDR = 0x30000000
 PARAMETER C_S1_AXI_HIGHADDR = 0x3000FFFF
 PARAMETER C_INTERCONNECT_S0_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_B_REGISTER = 8
 PARAMETER C_INTERCONNECT_S1_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_B_REGISTER = 7
 BUS_INTERFACE S0_AXI = mb_high_axi_periph
 BUS_INTERFACE S1_AXI = mb_low_axi_periph
 PORT S0_AXI_ACLK = clk_160MHz
 PORT S1_AXI_ACLK = clk_160MHz
 PORT Interrupt_0 = mb_mailbox_Interrupt_0
END

BEGIN mutex
 PARAMETER INSTANCE = pkt_buffer_mutex
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_NUM_PLB = 0
 PARAMETER C_NUM_AXI = 2
 PARAMETER C_NUM_MUTEX = 32
 PARAMETER C_ENABLE_USER = 1
 PARAMETER C_ENABLE_HW_PROT = 1
 PARAMETER C_INTERCONNECT_S0_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S0_AXI_B_REGISTER = 8
 PARAMETER C_S0_AXI_BASEADDR = 0x31000000
 PARAMETER C_S0_AXI_HIGHADDR = 0x3100FFFF
 PARAMETER C_S1_AXI_BASEADDR = 0x31000000
 PARAMETER C_S1_AXI_HIGHADDR = 0x3100FFFF
 PARAMETER C_INTERCONNECT_S1_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S1_AXI_B_REGISTER = 7
 BUS_INTERFACE S0_AXI = mb_high_axi_periph
 BUS_INTERFACE S1_AXI = mb_low_axi_periph
 PORT S0_AXI_ACLK = clk_160MHz
 PORT S1_AXI_ACLK = clk_160MHz
END

BEGIN axi_bram_ctrl
 PARAMETER INSTANCE = pkt_buff_TX_bram_ctrl
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_SINGLE_PORT_BRAM = 1
 PARAMETER C_S_AXI_DATA_WIDTH = 64
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = mb_high.M_AXI_DC & mb_low.M_AXI_DC & axi_cdma_0.M_AXI
 PARAMETER C_S_AXI_BASEADDR = 0x91000000
 PARAMETER C_S_AXI_HIGHADDR = 0x9100FFFF
 BUS_INTERFACE BRAM_PORTA = PKT_BUFF_TX_CTRL_PORTA
 BUS_INTERFACE S_AXI = mb_shared_axi
 PORT S_AXI_ACLK = clk_160MHz
END

BEGIN bram_block
 PARAMETER INSTANCE = pkt_buffer_TX_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = PKT_BUFF_TX_CTRL_PORTA
 BUS_INTERFACE PORTB = WLAN_TX_PKT_BUF_PORTB
 PORT BRAM_Clk_B = clk_160MHz
END

BEGIN axi_bram_ctrl
 PARAMETER INSTANCE = pkt_buff_RX_bram_ctrl
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_SINGLE_PORT_BRAM = 1
 PARAMETER C_S_AXI_DATA_WIDTH = 64
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = mb_low.M_AXI_DC & mb_high.M_AXI_DC & axi_cdma_0.M_AXI & axi2axi_eth_a_dma.M_AXI
 PARAMETER C_S_AXI_BASEADDR = 0x90000000
 PARAMETER C_S_AXI_HIGHADDR = 0x90007FFF
 BUS_INTERFACE BRAM_PORTA = PKT_BUFF_RX_CTRL_PORTA
 BUS_INTERFACE S_AXI = mb_shared_axi
 PORT S_AXI_ACLK = clk_160MHz
END

BEGIN bram_block
 PARAMETER INSTANCE = pkt_buffer_RX_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = PKT_BUFF_RX_CTRL_PORTA
 BUS_INTERFACE PORTB = WLAN_RX_PKT_BUF_PORTB
 PORT BRAM_Clk_B = clk_160MHz
END

BEGIN axi_interconnect
 PARAMETER INSTANCE = mb_shared_axi_periph
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PORT INTERCONNECT_ARESETN = sys_reset_Interconnect_aresetn
 PORT INTERCONNECT_ACLK = clk_160MHz
END

BEGIN axi2axi_connector
 PARAMETER INSTANCE = axi2axi_connector_shared_periphs
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = mb_low.M_AXI_DC & mb_high.M_AXI_DC
 PARAMETER C_S_AXI_RNG00_BASEADDR = 0x80000000
 PARAMETER C_S_AXI_RNG00_HIGHADDR = 0x8FFFFFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi
 BUS_INTERFACE M_AXI = mb_shared_axi_periph
END

BEGIN w3_userio_axi
 PARAMETER INSTANCE = w3_userio
 PARAMETER HW_VER = 1.03.a
 PARAMETER INCLUDE_DNA_READ_LOGIC = 0
 PARAMETER C_BASEADDR = 0x80000000
 PARAMETER C_HIGHADDR = 0x80000FFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT leds_red = userio_leds_red
 PORT leds_green = userio_leds_green
 PORT hexdisp_left = userio_hexdisp_left
 PORT hexdisp_right = userio_hexdisp_right
 PORT hexdisp_left_dp = userio_hexdisp_left_dp
 PORT hexdisp_right_dp = userio_hexdisp_right_dp
 PORT rfa_led_red = userio_rfa_led_red
 PORT rfa_led_green = userio_rfa_led_green
 PORT rfb_led_red = userio_rfb_led_red
 PORT rfb_led_green = userio_rfb_led_green
 PORT dipsw = userio_dipsw_b0 & userio_dipsw_b1 & userio_dipsw_b2 & userio_dipsw_b3
 PORT pb_u = userio_pb_u
 PORT pb_m = userio_pb_m
 PORT pb_d = userio_pb_d
 PORT usr_rfa_led_red = RFA_statLED_Rx
 PORT usr_rfa_led_green = RFA_statLED_Tx
 PORT usr_rfb_led_red = RFB_statLED_Rx
 PORT usr_rfb_led_green = RFB_statLED_Tx
 PORT usr_leds_red = dbg_signal_err_disp
 PORT usr_dbg_hdr_out = dbg_mac_tx_d_pending & dbg_mac_tx_c_pending & dbg_mac_backoff_c_active & dbg_mac_tx_b_pending & dbg_mac_nav_active & dbg_mac_backoff_a_active & dbg_mac_idle_for_difs & dbg_mac_tx_a_pending & dbg_rssi_det & mac_phy_rx_fcs_good_ind & dbg_lts_timeout & dbg_pkt_det_dsss & dbg_pkt_det_ofdm & dbg_dsss_rx_active & dbg_ofdm_rx_active & dbg_tx_running
 PORT dbg_hdr = dbg_hdr
END

BEGIN wlan_mac_time_hw_axiw
 PARAMETER INSTANCE = wlan_mac_time_hw
 PARAMETER HW_VER = 1.00.d
 PARAMETER C_BASEADDR = 0x81000000
 PARAMETER C_HIGHADDR = 0x81000FFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi_periph
 PORT axi_aclk = clk_160MHz
 PORT sysgen_clk = clk_160MHz
 PORT mac_time_lsb = mac_time_usec_lsb
 PORT mac_time_msb = mac_time_usec_msb
 PORT time_usec_frac = mac_time_usec_frac
END

BEGIN w3_iic_eeprom_axi
 PARAMETER INSTANCE = w3_iic_eeprom_onBoard
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BASEADDR = 0x82000000
 PARAMETER C_HIGHADDR = 0x8200FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT iic_scl_I = axi_iic_eeprom_scl_I
 PORT iic_scl_O = axi_iic_eeprom_scl_O
 PORT iic_scl_T = axi_iic_eeprom_scl_T
 PORT iic_sda_I = axi_iic_eeprom_sda_I
 PORT iic_sda_O = axi_iic_eeprom_sda_O
 PORT iic_sda_T = axi_iic_eeprom_sda_T
END

BEGIN axi_sysmon_adc
 PARAMETER INSTANCE = axi_sysmon
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_INCLUDE_INTR = 1
 PARAMETER C_BASEADDR = 0x83000000
 PARAMETER C_HIGHADDR = 0x83000FFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT VAUXP = net_gnd
 PORT VAUXN = net_gnd
 PORT CONVST = net_gnd
END

# ##############################################################################
# Microblaze Low
# ##############################################################################
BEGIN microblaze
 PARAMETER INSTANCE = mb_low
 PARAMETER HW_VER = 8.40.b
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_USE_DCACHE = 1
 PARAMETER C_USE_ICACHE = 0
# Little endian
 PARAMETER C_ENDIANNESS = 1
# MMU Settings
 PARAMETER C_USE_MMU = 0
 PARAMETER C_M_AXI_D_BUS_EXCEPTION = 1
 PARAMETER C_ILL_OPCODE_EXCEPTION = 1
 PARAMETER C_UNALIGNED_EXCEPTIONS = 1
 PARAMETER C_OPCODE_0x0_ILLEGAL = 1
 PARAMETER C_USE_BARREL = 1
 PARAMETER C_PVR = 2
 PARAMETER C_INTERCONNECT_M_AXI_DC_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_DC_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_DC_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_DC_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_DC_B_REGISTER = 7
 PARAMETER C_NUMBER_OF_PC_BRK = 4
 PARAMETER C_NUMBER_OF_WR_ADDR_BRK = 2
 PARAMETER C_NUMBER_OF_RD_ADDR_BRK = 2
 PARAMETER C_CACHE_BYTE_SIZE = 64
 PARAMETER C_DCACHE_BYTE_SIZE = 64
 PARAMETER C_DCACHE_BASEADDR = 0x80000000
 PARAMETER C_DCACHE_HIGHADDR = 0xffffffff
 PARAMETER C_DCACHE_ALWAYS_USED = 1
 PARAMETER C_USE_STACK_PROTECTION = 1
 PARAMETER C_USE_DIV = 1
 BUS_INTERFACE M_AXI_DC = mb_shared_axi
 BUS_INTERFACE M_AXI_DP = mb_low_axi_periph
 BUS_INTERFACE DEBUG = mb_low_debug
 BUS_INTERFACE DLMB = mb_low_dlmb
 BUS_INTERFACE ILMB = mb_low_ilmb
 PORT MB_RESET = sys_reset_MB_Reset
 PORT CLK = clk_160MHz
 PORT INTERRUPT = net_gnd
END

BEGIN bram_block
 PARAMETER INSTANCE = mb_low_lmb_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = mb_low_ilmb_bram_PORT
 BUS_INTERFACE PORTB = mb_low_dlmb_bram_PORT
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_low_ilmb_bram_cntlr
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0001ffff
 BUS_INTERFACE BRAM_PORT = mb_low_ilmb_bram_PORT
 BUS_INTERFACE SLMB = mb_low_ilmb
END

BEGIN lmb_v10
 PARAMETER INSTANCE = mb_low_ilmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = sys_reset_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_160MHz
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_low_dlmb_bram_cntlr
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0001ffff
 BUS_INTERFACE BRAM_PORT = mb_low_dlmb_bram_PORT
 BUS_INTERFACE SLMB = mb_low_dlmb
END

BEGIN lmb_v10
 PARAMETER INSTANCE = mb_low_dlmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = sys_reset_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_160MHz
END

# ##############################################################################
# Microblaze Low Standard Peripherals
# ##############################################################################
BEGIN axi_interconnect
 PARAMETER INSTANCE = mb_low_axi_periph
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PORT INTERCONNECT_ACLK = clk_160MHz
 PORT INTERCONNECT_ARESETN = sys_reset_Interconnect_aresetn
END

BEGIN axi_uartlite
 PARAMETER INSTANCE = mb_low_uart
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BAUDRATE = 115200
 PARAMETER C_BASEADDR = 0x20000000
 PARAMETER C_HIGHADDR = 0x2000FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_low_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
# RX=input to uartartlite (PC -> FPGA)
# TX=output from uartlite (FPGA -> PC)
 PORT RX = mb_low_uart_RX
 PORT TX = mb_low_uart_TX
END

# ##############################################################################
# Microblaze High
# ##############################################################################
BEGIN microblaze
 PARAMETER INSTANCE = mb_high
 PARAMETER HW_VER = 8.40.b
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_USE_DCACHE = 1
 PARAMETER C_USE_ICACHE = 0
# Little endian
 PARAMETER C_ENDIANNESS = 1
# MMU Settings
 PARAMETER C_USE_MMU = 0
 PARAMETER C_M_AXI_D_BUS_EXCEPTION = 1
 PARAMETER C_ILL_OPCODE_EXCEPTION = 1
 PARAMETER C_UNALIGNED_EXCEPTIONS = 1
 PARAMETER C_OPCODE_0x0_ILLEGAL = 1
 PARAMETER C_USE_BARREL = 1
 PARAMETER C_PVR = 2
 PARAMETER C_INTERCONNECT_M_AXI_DC_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_DC_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_DC_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_DC_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_DC_B_REGISTER = 7
 PARAMETER C_NUMBER_OF_PC_BRK = 4
 PARAMETER C_NUMBER_OF_WR_ADDR_BRK = 2
 PARAMETER C_NUMBER_OF_RD_ADDR_BRK = 2
 PARAMETER C_CACHE_BYTE_SIZE = 64
 PARAMETER C_DCACHE_BYTE_SIZE = 64
 PARAMETER C_DCACHE_BASEADDR = 0x80000000
 PARAMETER C_DCACHE_HIGHADDR = 0xffffffff
 PARAMETER C_INTERCONNECT_M_AXI_DP_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_M_AXI_DP_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_M_AXI_DP_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_M_AXI_DP_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_M_AXI_DP_B_REGISTER = 8
 PARAMETER C_DCACHE_ALWAYS_USED = 1
 PARAMETER C_USE_STACK_PROTECTION = 1
 BUS_INTERFACE M_AXI_DC = mb_shared_axi
 BUS_INTERFACE M_AXI_DP = mb_high_axi_periph
 BUS_INTERFACE DEBUG = mb_high_debug
 BUS_INTERFACE INTERRUPT = mb_high_interrupt
 BUS_INTERFACE DLMB = mb_high_dlmb
 BUS_INTERFACE ILMB = mb_high_ilmb
 PORT MB_RESET = sys_reset_MB_Reset
 PORT CLK = clk_160MHz
END

BEGIN lmb_v10
 PARAMETER INSTANCE = mb_high_dlmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = sys_reset_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_160MHz
END

BEGIN lmb_v10
 PARAMETER INSTANCE = mb_high_ilmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = sys_reset_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_160MHz
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_high_dlmb_bram_cntlr_0
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0001FFFF
 BUS_INTERFACE SLMB = mb_high_dlmb
 BUS_INTERFACE BRAM_PORT = mb_high_dlmb_bram_cntlr_0_BRAM_PORT
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_high_ilmb_bram_cntlr_0
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0001FFFF
 BUS_INTERFACE SLMB = mb_high_ilmb
 BUS_INTERFACE BRAM_PORT = mb_high_ilmb_bram_cntlr_0_BRAM_PORT
END

BEGIN bram_block
 PARAMETER INSTANCE = mb_high_lmb_bram_0
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTB = mb_high_ilmb_bram_cntlr_0_BRAM_PORT
 BUS_INTERFACE PORTA = mb_high_dlmb_bram_cntlr_0_BRAM_PORT
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_high_dlmb_bram_cntlr_1
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00020000
 PARAMETER C_HIGHADDR = 0x0003FFFF
 BUS_INTERFACE SLMB = mb_high_dlmb
 BUS_INTERFACE BRAM_PORT = mb_high_dlmb_bram_cntlr_1_BRAM_PORT
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb_high_ilmb_bram_cntlr_1
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00020000
 PARAMETER C_HIGHADDR = 0x0003FFFF
 BUS_INTERFACE SLMB = mb_high_ilmb
 BUS_INTERFACE BRAM_PORT = mb_high_ilmb_bram_cntlr_1_BRAM_PORT
END

BEGIN bram_block
 PARAMETER INSTANCE = mb_high_lmb_bram_1
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = mb_high_dlmb_bram_cntlr_1_BRAM_PORT
 BUS_INTERFACE PORTB = mb_high_ilmb_bram_cntlr_1_BRAM_PORT
END

# ##############################################################################
# Microblaze High Standard Peripherals
# ##############################################################################
BEGIN axi_interconnect
 PARAMETER INSTANCE = mb_high_axi_periph
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PORT INTERCONNECT_ARESETN = sys_reset_Interconnect_aresetn
 PORT INTERCONNECT_ACLK = clk_160MHz
END

BEGIN axi_uartlite
 PARAMETER INSTANCE = mb_high_uart
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BAUDRATE = 115200
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x21000000
 PARAMETER C_HIGHADDR = 0x2100FFFF
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
# RX=input to uartartlite (PC -> FPGA)
# TX=output from uartlite (FPGA -> PC)
 PORT RX = mb_high_uart_RX
 PORT TX = mb_high_uart_TX
 PORT Interrupt = mb_high_uart_Interrupt
END

BEGIN sw_intr_util
 PARAMETER INSTANCE = high_sw_intr_util
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x23010000
 PARAMETER C_HIGHADDR = 0x2301FFFF
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT intrA_out = SW_INTR_A
 PORT intrB_out = SW_INTR_B
END

BEGIN axi_timer
 PARAMETER INSTANCE = mb_high_timer
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x23000000
 PARAMETER C_HIGHADDR = 0x2300FFFF
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT Interrupt = mb_high_timer_Interrupt
END

BEGIN axi_intc
 PARAMETER INSTANCE = mb_high_intc
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_BASEADDR = 0x22000000
 PARAMETER C_HIGHADDR = 0x2200FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 BUS_INTERFACE INTERRUPT = mb_high_interrupt
 PORT Intr = SW_INTR_B & ETH_A_MAC_INTERRUPT & ETH_B_MAC_INTERRUPT & mb_high_sw_gpio_IP2INTC_Irpt & mb_high_uart_Interrupt & ETH_A_DMA_mm2s_introut & ETH_A_DMA_s2mm_introut & ETH_B_DMA_mm2s_introut & ETH_B_DMA_s2mm_introut & SW_INTR_A & mb_high_timer_Interrupt & mb_mailbox_Interrupt_0
 PORT S_AXI_ACLK = clk_160MHz
END

BEGIN axi_gpio
 PARAMETER INSTANCE = mb_high_sw_gpio
 PARAMETER HW_VER = 1.01.b
 PARAMETER C_BASEADDR = 0x20000000
 PARAMETER C_HIGHADDR = 0x2000FFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_GPIO_WIDTH = 9
 PARAMETER C_ALL_INPUTS = 1
 PARAMETER C_INTERRUPT_PRESENT = 1
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 PORT S_AXI_ACLK = clk_160MHz
 PORT GPIO_IO_I = dram_init_done & 0b0 & userio_pb_u & userio_pb_m & userio_pb_d & userio_dipsw_b0 & userio_dipsw_b1 & userio_dipsw_b2 & userio_dipsw_b3
 PORT IP2INTC_Irpt = mb_high_sw_gpio_IP2INTC_Irpt
END

BEGIN axi_bram_ctrl
 PARAMETER INSTANCE = mb_high_aux_bram_ctrl
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_S_AXI_DATA_WIDTH = 64
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = mb_high.M_AXI_DC & axi2axi_eth_a_dma.M_AXI & axi2axi_eth_b_dma.M_AXI
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_S_AXI_BASEADDR = 0xA0000000
 PARAMETER C_S_AXI_HIGHADDR = 0xA000FFFF
 BUS_INTERFACE BRAM_PORTA = MB_HIGH_AUX_BRAM_PORTA
 BUS_INTERFACE BRAM_PORTB = MB_HIGH_AUX_BRAM_PORTB
 BUS_INTERFACE S_AXI = mb_shared_axi
 PORT S_AXI_ACLK = clk_160MHz
END

BEGIN bram_block
 PARAMETER INSTANCE = mb_high_aux_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = MB_HIGH_AUX_BRAM_PORTA
 BUS_INTERFACE PORTB = MB_HIGH_AUX_BRAM_PORTB
END

BEGIN axi_cdma
 PARAMETER INSTANCE = axi_cdma_0
 PARAMETER HW_VER = 3.04.a
 PARAMETER C_M_AXI_DATA_WIDTH = 64
 PARAMETER C_M_AXI_MAX_BURST_LEN = 64
 PARAMETER C_INCLUDE_DRE = 1
 PARAMETER C_INTERCONNECT_M_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x48000000
 PARAMETER C_HIGHADDR = 0x4800FFFF
 BUS_INTERFACE S_AXI_LITE = mb_high_axi_periph
 BUS_INTERFACE M_AXI = mb_shared_axi
 PORT s_axi_lite_aclk = clk_160MHz
 PORT m_axi_aclk = clk_160MHz
END

# ##############################################################################
# Ethernet
# ##############################################################################
BEGIN axi_interconnect
 PARAMETER INSTANCE = ethernet_axi
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_DATA_WIDTH = 64
 PORT INTERCONNECT_ACLK = clk_160MHz
 PORT INTERCONNECT_ARESETN = sys_reset_Interconnect_aresetn
END

BEGIN axi2axi_connector
 PARAMETER INSTANCE = axi2axi_eth_a_dma
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = ETH_A_DMA.M_AXI_SG & ETH_A_DMA.M_AXI_MM2S & ETH_A_DMA.M_AXI_S2MM
 PARAMETER C_S_AXI_RNG00_BASEADDR = 0x00000000
 PARAMETER C_S_AXI_RNG00_HIGHADDR = 0xFFFFFFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = ethernet_axi
 BUS_INTERFACE M_AXI = mb_shared_axi
END

BEGIN axi2axi_connector
 PARAMETER INSTANCE = axi2axi_eth_b_dma
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = ETH_B_DMA.M_AXI_SG & ETH_B_DMA.M_AXI_MM2S & ETH_B_DMA.M_AXI_S2MM
 PARAMETER C_S_AXI_RNG00_BASEADDR = 0x00000000
 PARAMETER C_S_AXI_RNG00_HIGHADDR = 0xFFFFFFFF
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = ethernet_axi
 BUS_INTERFACE M_AXI = mb_shared_axi
END

BEGIN axi_ethernet
 PARAMETER INSTANCE = ETH_A_MAC
 PARAMETER HW_VER = 3.01.a
# ETH_A PHY Address = 6 on WARP v3 1.1
 PARAMETER C_PHYADDR = 0B00110
 PARAMETER C_INCLUDE_IO = 1
 PARAMETER C_TYPE = 2
 PARAMETER C_PHY_TYPE = 3
 PARAMETER C_HALFDUP = 0
 PARAMETER C_TXMEM = 16384
 PARAMETER C_RXMEM = 16384
 PARAMETER C_TXCSUM = 0
 PARAMETER C_RXCSUM = 0
 PARAMETER C_TXVLAN_TRAN = 0
 PARAMETER C_RXVLAN_TRAN = 0
 PARAMETER C_TXVLAN_TAG = 0
 PARAMETER C_RXVLAN_TAG = 0
 PARAMETER C_TXVLAN_STRP = 0
 PARAMETER C_RXVLAN_STRP = 0
 PARAMETER C_MCAST_EXTEND = 0
 PARAMETER C_STATS = 0
 PARAMETER C_AVB = 0
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x40000000
 PARAMETER C_HIGHADDR = 0x4003FFFF
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 BUS_INTERFACE AXI_STR_RXD = ETH_A_MAC_AXIS_RXD
 BUS_INTERFACE AXI_STR_RXS = ETH_A_MAC_AXIS_RXS
 BUS_INTERFACE AXI_STR_TXD = ETH_A_MAC_AXIS_TXD
 BUS_INTERFACE AXI_STR_TXC = ETH_A_MAC_AXIS_TXC
 PORT S_AXI_ACLK = clk_160MHz
 PORT GTX_CLK = clk_125MHz
 PORT PHY_RST_N = ETH_A_PHY_RST_N
 PORT MDIO = ETH_A_MDIO
 PORT MDC = ETH_A_MDC
 PORT REF_CLK = clk_200MHz
# AXI Stream connections (to FIFO or DMA)
 PORT AXI_STR_TXD_ACLK = clk_160MHz
 PORT AXI_STR_TXC_ACLK = clk_160MHz
 PORT AXI_STR_RXD_ACLK = clk_160MHz
 PORT AXI_STR_RXS_ACLK = clk_160MHz
# RGMII connections (to Eth PHY IC on PCB)
 PORT RGMII_TXD = ETH_A_RGMII_TXD
 PORT RGMII_TX_CTL = ETH_A_RGMII_TX_CTL
 PORT RGMII_TXC = ETH_A_RGMII_TXC
 PORT RGMII_RXD = ETH_A_RGMII_RXD
 PORT RGMII_RX_CTL = ETH_A_RGMII_RX_CTL
 PORT RGMII_RXC = ETH_A_RGMII_RXC
 PORT INTERRUPT = ETH_A_MAC_INTERRUPT
END

BEGIN axi_dma
 PARAMETER INSTANCE = ETH_A_DMA
 PARAMETER HW_VER = 6.03.a
 PARAMETER C_SG_INCLUDE_DESC_QUEUE = 1
 PARAMETER C_M_AXI_MM2S_DATA_WIDTH = 64
 PARAMETER C_INCLUDE_MM2S_DRE = 1
 PARAMETER C_M_AXI_S2MM_DATA_WIDTH = 64
 PARAMETER C_INCLUDE_S2MM_DRE = 1
 PARAMETER C_BASEADDR = 0x42000000
 PARAMETER C_HIGHADDR = 0x4200FFFF
 PARAMETER C_INTERCONNECT_M_AXI_SG_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_SG_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_SG_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_SG_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_SG_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_B_REGISTER = 8
 BUS_INTERFACE S_AXI_LITE = mb_high_axi_periph
 BUS_INTERFACE M_AXI_SG = ethernet_axi
 BUS_INTERFACE M_AXI_MM2S = ethernet_axi
 BUS_INTERFACE M_AXI_S2MM = ethernet_axi
 BUS_INTERFACE S_AXIS_S2MM = ETH_A_MAC_AXIS_RXD
 BUS_INTERFACE S_AXIS_S2MM_STS = ETH_A_MAC_AXIS_RXS
 BUS_INTERFACE M_AXIS_MM2S = ETH_A_MAC_AXIS_TXD
 BUS_INTERFACE M_AXIS_MM2S_CNTRL = ETH_A_MAC_AXIS_TXC
 PORT s_axi_lite_aclk = clk_160MHz
 PORT m_axi_sg_aclk = clk_160MHz
 PORT m_axi_mm2s_aclk = clk_160MHz
 PORT m_axi_s2mm_aclk = clk_160MHz
 PORT mm2s_introut = ETH_A_DMA_mm2s_introut
 PORT s2mm_introut = ETH_A_DMA_s2mm_introut
 PORT s_axis_s2mm_tuser = net_gnd
 PORT s_axis_s2mm_tid = net_gnd
 PORT s_axis_s2mm_tdest = net_gnd
END

BEGIN axi_ethernet
 PARAMETER INSTANCE = ETH_B_MAC
 PARAMETER HW_VER = 3.01.a
# ETH_B PHY Address = 7 on WARP v3 1.1
 PARAMETER C_PHYADDR = 0B00111
 PARAMETER C_INCLUDE_IO = 1
 PARAMETER C_TYPE = 2
 PARAMETER C_PHY_TYPE = 3
 PARAMETER C_HALFDUP = 0
 PARAMETER C_TXMEM = 16384
 PARAMETER C_RXMEM = 16384
 PARAMETER C_TXCSUM = 0
 PARAMETER C_RXCSUM = 0
 PARAMETER C_TXVLAN_TRAN = 0
 PARAMETER C_RXVLAN_TRAN = 0
 PARAMETER C_TXVLAN_TAG = 0
 PARAMETER C_RXVLAN_TAG = 0
 PARAMETER C_TXVLAN_STRP = 0
 PARAMETER C_RXVLAN_STRP = 0
 PARAMETER C_MCAST_EXTEND = 0
 PARAMETER C_STATS = 0
 PARAMETER C_AVB = 0
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 8
 PARAMETER C_BASEADDR = 0x41000000
 PARAMETER C_HIGHADDR = 0x4103FFFF
 BUS_INTERFACE S_AXI = mb_high_axi_periph
 BUS_INTERFACE AXI_STR_RXD = ETH_B_MAC_AXIS_RXD
 BUS_INTERFACE AXI_STR_RXS = ETH_B_MAC_AXIS_RXS
 BUS_INTERFACE AXI_STR_TXD = ETH_B_MAC_AXIS_TXD
 BUS_INTERFACE AXI_STR_TXC = ETH_B_MAC_AXIS_TXC
 PORT S_AXI_ACLK = clk_160MHz
 PORT GTX_CLK = clk_125MHz
# PORT PHY_RST_N = ETH_B_PHY_RST_N
 PORT MDIO = ETH_B_MDIO
 PORT MDC = ETH_B_MDC
 PORT REF_CLK = clk_200MHz
# AXI Stream connections (to FIFO or DMA)
 PORT AXI_STR_TXD_ACLK = clk_160MHz
 PORT AXI_STR_TXC_ACLK = clk_160MHz
 PORT AXI_STR_RXD_ACLK = clk_160MHz
 PORT AXI_STR_RXS_ACLK = clk_160MHz
 PORT AXI_STR_RXS_TREADY = net_vcc
# RGMII connections (to Eth PHY IC on PCB)
 PORT RGMII_TXD = ETH_B_RGMII_TXD
 PORT RGMII_TX_CTL = ETH_B_RGMII_TX_CTL
 PORT RGMII_TXC = ETH_B_RGMII_TXC
 PORT RGMII_RXD = ETH_B_RGMII_RXD
 PORT RGMII_RX_CTL = ETH_B_RGMII_RX_CTL
 PORT RGMII_RXC = ETH_B_RGMII_RXC
 PORT INTERRUPT = ETH_B_MAC_INTERRUPT
END

BEGIN axi_dma
 PARAMETER INSTANCE = ETH_B_DMA
 PARAMETER HW_VER = 6.03.a
 PARAMETER C_SG_INCLUDE_DESC_QUEUE = 1
 PARAMETER C_M_AXI_MM2S_DATA_WIDTH = 64
 PARAMETER C_INCLUDE_MM2S_DRE = 1
 PARAMETER C_M_AXI_S2MM_DATA_WIDTH = 64
 PARAMETER C_INCLUDE_S2MM_DRE = 1
 PARAMETER C_BASEADDR = 0x43000000
 PARAMETER C_HIGHADDR = 0x4300FFFF
 PARAMETER C_INTERCONNECT_M_AXI_SG_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_SG_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_SG_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_SG_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_SG_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_MM2S_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_M_AXI_S2MM_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AW_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_AR_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_W_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_R_REGISTER = 8
 PARAMETER C_INTERCONNECT_S_AXI_LITE_B_REGISTER = 8
 BUS_INTERFACE S_AXI_LITE = mb_high_axi_periph
 BUS_INTERFACE M_AXI_SG = ethernet_axi
 BUS_INTERFACE M_AXI_MM2S = ethernet_axi
 BUS_INTERFACE M_AXI_S2MM = ethernet_axi
 BUS_INTERFACE S_AXIS_S2MM = ETH_B_MAC_AXIS_RXD
 BUS_INTERFACE S_AXIS_S2MM_STS = ETH_B_MAC_AXIS_RXS
 BUS_INTERFACE M_AXIS_MM2S_CNTRL = ETH_B_MAC_AXIS_TXC
 BUS_INTERFACE M_AXIS_MM2S = ETH_B_MAC_AXIS_TXD
 PORT s_axi_lite_aclk = clk_160MHz
 PORT m_axi_sg_aclk = clk_160MHz
 PORT m_axi_mm2s_aclk = clk_160MHz
 PORT m_axi_s2mm_aclk = clk_160MHz
 PORT mm2s_introut = ETH_B_DMA_mm2s_introut
 PORT s2mm_introut = ETH_B_DMA_s2mm_introut
 PORT s_axis_s2mm_tuser = net_gnd
 PORT s_axis_s2mm_tid = net_gnd
 PORT s_axis_s2mm_tdest = net_gnd
END

# ##############################################################################
# DDR
# ##############################################################################
BEGIN axi_v6_ddrx
 PARAMETER INSTANCE = DDR3_SODIMM
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_MEM_PARTNO = MT8JSF25664HZ-1G4
 PARAMETER C_CK_WIDTH = 2
 PARAMETER C_ROW_WIDTH = 15
 PARAMETER C_MMCM_EXT_LOC = MMCM_ADV_X0Y0
# Manually entered params (extracted from MIG-ISE test design that worked in hardware)
 PARAMETER C_NDQS_COL0 = 5
 PARAMETER C_NDQS_COL1 = 3
 PARAMETER C_NDQS_COL2 = 0
 PARAMETER C_NDQS_COL3 = 0
 PARAMETER C_DQS_LOC_COL0 = 0x0403020100
 PARAMETER C_DQS_LOC_COL1 = 0x0000070605
 PARAMETER C_ECC = OFF
# END Manually entered params
 PARAMETER C_TCK = 3125
 PARAMETER C_S_AXI_DATA_WIDTH = 64
 PARAMETER C_S_AXI_BASEADDR = 0xc0000000
 PARAMETER C_S_AXI_HIGHADDR = 0xffffffff
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = axi2axi_eth_a_dma.M_AXI & axi2axi_eth_b_dma.M_AXI & mb_high.M_AXI_DC & axi_cdma_0.M_AXI
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 1
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 BUS_INTERFACE S_AXI = mb_shared_axi
 PORT clk = clk_160MHz
 PORT clk_mem = clk_dram_320MHz_clk_mem
 PORT clk_rd_base = clk_dram_320MHz_clk_rd_base
 PORT clk_ref = clk_200MHz
 PORT pd_PSEN = MMCM_PSEN
 PORT pd_PSINCDEC = MMCM_PSINCDEC
 PORT pd_PSDONE = MMCM_PSDONE
 PORT ddr_ck_p = ddr3_sodimm_ck_p
 PORT ddr_ck_n = ddr3_sodimm_ck_n
 PORT ddr_cke = ddr3_sodimm_cke
 PORT ddr_cs_n = ddr3_sodimm_cs_n
 PORT ddr_odt = ddr3_sodimm_odt
 PORT ddr_ras_n = ddr3_sodimm_ras_n
 PORT ddr_cas_n = ddr3_sodimm_cas_n
 PORT ddr_we_n = ddr3_sodimm_we_n
 PORT ddr_ba = ddr3_sodimm_ba
 PORT ddr_addr = ddr3_sodimm_addr
 PORT ddr_dq = ddr3_sodimm_dq
 PORT ddr_dm = ddr3_sodimm_dm
 PORT ddr_reset_n = ddr3_sodimm_reset_n
 PORT ddr_dqs_p = ddr3_sodimm_dqs_p
 PORT ddr_dqs_n = ddr3_sodimm_dqs_n
 PORT phy_init_done = dram_init_done
END

# ##############################################################################
# Debug / Misc Logic
# ##############################################################################
BEGIN mdm
 PARAMETER INSTANCE = debug_module
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_USE_UART = 0
 PARAMETER C_MB_DBG_PORTS = 2
 PARAMETER C_INTERCONNECT_S_AXI_AW_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_AR_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_W_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_R_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_B_REGISTER = 7
 PARAMETER C_INTERCONNECT_S_AXI_MASTERS = mb_low.M_AXI_DC & mb_high.M_AXI_DC
 BUS_INTERFACE MBDEBUG_0 = mb_low_debug
 BUS_INTERFACE MBDEBUG_1 = mb_high_debug
 PORT Debug_SYS_Rst = sys_reset_debug_rst
 PORT S_AXI_ACLK = clk_160MHz
END

BEGIN util_reduced_logic
 PARAMETER INSTANCE = clk_gen_locked_AND
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_OPERATION = AND
 PARAMETER C_SIZE = 3
 PORT Op1 = clk_gen_proc_bus_clks_locked & clk_gen_async_clks_locked & clk_gen_dram_clks_locked
 PORT Res = clk_gen_all_locked
END

BEGIN uart_mux
 PARAMETER INSTANCE = usb_uart_mux
 PARAMETER HW_VER = 1.00.a
 PARAMETER MIRROR_UART_RX = 0
 PORT uart_sel = userio_dipsw_b3
 PORT uart_tx = mb_uart_mux_tx
 PORT uart_rx = usb_uart_rx
 PORT uart_0_tx = mb_low_uart_TX
 PORT uart_0_rx = mb_low_uart_RX
 PORT uart_1_tx = mb_high_uart_TX
 PORT uart_1_rx = mb_high_uart_RX
END

BEGIN w3_boot_io_mux
 PARAMETER INSTANCE = boot_io_mux
 PARAMETER HW_VER = 1.00.a
# Mux Control
 PORT iic_sel_a = mmcm_inputs_invalid
 PORT uart_sel_a = mmcm_inputs_invalid
# IOBs
 PORT iic_scl = iic_eeprom_onboard_scl
 PORT iic_sda = iic_eeprom_onboard_sda
 PORT uart_tx = usb_uart_tx
# IIC Port A
 PORT iic_scl_I_a = clk_cfg_iic_eeprom_scl_I
 PORT iic_scl_O_a = clk_cfg_iic_eeprom_scl_O
 PORT iic_scl_T_a = clk_cfg_iic_eeprom_scl_T
 PORT iic_sda_I_a = clk_cfg_iic_eeprom_sda_I
 PORT iic_sda_O_a = clk_cfg_iic_eeprom_sda_O
 PORT iic_sda_T_a = clk_cfg_iic_eeprom_sda_T
# IIC Port B
 PORT iic_scl_I_b = axi_iic_eeprom_scl_I
 PORT iic_scl_O_b = axi_iic_eeprom_scl_O
 PORT iic_scl_T_b = axi_iic_eeprom_scl_T
 PORT iic_sda_I_b = axi_iic_eeprom_sda_I
 PORT iic_sda_O_b = axi_iic_eeprom_sda_O
 PORT iic_sda_T_b = axi_iic_eeprom_sda_T
# UART Ports
 PORT uart_tx_a = clk_cfg_uart_tx
 PORT uart_tx_b = mb_uart_mux_tx
END

BEGIN util_flipflop
 PARAMETER INSTANCE = dff_rssi_rfa
 PARAMETER HW_VER = 1.10.a
 PARAMETER C_SIZE = 10
 PARAMETER C_USE_RST = 0
 PARAMETER C_USE_SET = 0
 PARAMETER C_USE_CE = 0
 PARAMETER C_USE_ASYNCH = 0
 PORT CLK = clk_160MHz
 PORT D = RFA_RSSI_D
 PORT Q = RFA_RSSI_D_REG
END

BEGIN util_flipflop
 PARAMETER INSTANCE = dff_rssi_rfb
 PARAMETER HW_VER = 1.10.a
 PARAMETER C_SIZE = 10
 PARAMETER C_USE_RST = 0
 PARAMETER C_USE_SET = 0
 PARAMETER C_USE_CE = 0
 PARAMETER C_USE_ASYNCH = 0
 PORT CLK = clk_160MHz
 PORT D = RFB_RSSI_D
 PORT Q = RFB_RSSI_D_REG
END