wiki:HardwareUsersGuides/FPGABoard_v2.2/Power

Version 3 (modified by murphpo, 14 years ago) (diff)

--

WARP FPGA Board Power Supplies

Required External Supply

The WARP FPGA board operates from a single external 12v supply. This supply is generally connected to the board's coaxial power connector. This connector requires a mating female connector with an inner diameter of 2.1mm, outer diameter of 5.5mm, positive tip and grounded shell. We use a 50W AC-DC regulator from CUI (ETS120416UTC-P5P-SZ), available from Digikey (part T1010-P5P-ND).

FPGA Power Supplies

The Virtex-4 FPGA has a number of different power inputs. The table below summarizes the power supplies on the WARP FPGA board.

SupplyVoltageDescription
VCC_EXT12vExternal supply
VCC_55.0vDaughtercard slot supply
VCC_INT1.2vFPGA core logic
VCC_AUX2.5vFPGA clock resources
VCC_O3.3v, 2.5v & 1.8vFPGA I/O banks
MGT_x2.5v, 1.5v & 1.2vMGT logic and I/O
VCC_0.90.9vDDR2 SO-DIMM termination

The WARP FPGA board uses switching voltage regulators for the 5v, 3.3v, 1.8v and 1.2v supplies. All are are Texas Instruments' PTH12020W 18A DC-DC power modules.

The 2.5v VCC_AUX supply is a LT1764 linear regulator from Linear Technology.

The MGT supplies are all driven by linear supplies in order to minimize noise in the MGT circuitry. Three linear regulators (2 LT1963A and 1 LT1764) are used.

Daughtercard Power Supplies

The four daughtercard slots on the WARP FPGA board are supplied with 5v by a dedicated 18A switching regulator. A second power plane is also connected to the daughtercard slots and can be driven by an off-board supply via a dedicated 6-pin header on the FPGA board (J31). This header is not mounted by default (no current WARP daughtercards utilize this second plane).

Monitoring Voltage Levels

Every power and ground plane on the FPGA board includes a test point or screw terminal which can be used to monitor the plane's voltage. There are also test points and a screw terminal for ground. The locations of the test points and screw terminals are illustrated in the figure below.

No image "FPGABoard_PowerLocations.jpg" attached to HardwareUsersGuides/FPGABoard_v2.2/Images

Most supplies (12v, 5v, 3.3v, digital 2.5v and MGT 2.5v) include a red LED which glows when power is applied. These five LEDs should always be illuminated when the FPGA board is powered on. If any of these LEDs is not glowing, immediately power off the board to avoid damaging components.

Bypassing Power Supplies

The WARP FPGA board does not contain any built-in current measurement capabilities. In order to measure current consumption, the power plane of interest can be driven by an external, off-board supply whose current can be measured. When an external supply is used, the on-board regulator for the plane must be disabled to avoid a drive fight between the on-board and off-board supplies. Eight of the FPGA board's supplies (5v, 3.3v, 2.5v, 1.8v, 1.2v, MGT 2.5, MGT 1.5 and MGT 1.2v) can be individually disabled. To disable these regulators, simply mount a shunt on the jumper adjascent to the regulator; see the table below for the specific reference designators for each jumper.

High-current screw terminals are connected to the primary power planes: GND, 12v, 5v, 3.3v, 1.8v and 1.2v and can be used to connect external supplies. See the image below to identify the screw terminals.

Primary Supplies

PlaneRegulatorDisable
Jumper
Screw
Terminal
Test
Point
12v Ext - J35 TP14
5v U18 J32 J38 TP12
3.3v U16 J33 J37 TP11
2.5v U8 J40 - TP8
1.8v U13 J42 J36 TP10
1.2v U11 J43 J35 TP13
GND - - J34 TP9

MGT Supplies

PlaneRegulatorDisable
Jumper
Test
Point
2.5v J3 J8 TP5
1.5v U2 J7 TP4
1.2v U1 J9 TP1