source: ResearchApps/PHY/WARPLAB/WARPLab7/XPS_Reference/w2_4RF/system.mhs

# ##############################################################################
# WARPLab Reference Design
# XPS Hardware Specification (system.mhs)
# Copyright 2013 Mango Communications
# Distributed under the WARP license  (http://warpproject.org/license)
# Target Board:              Rice University - WARP Project WARP Kits (FPGA/Clock/Radio Boards) Rev FPGA 2.2 / Radio 1.4 / Clock 1.1
# WARPLab version:           7.5.0
# Family:                    virtex4
# Device:                    XC4VFX100
# Package:                   FF1517
# Speed Grade:               -11
# Processor number:          1
# Processor 1:               ppc405_0
# Processor clock frequency: 160.0
# Bus clock frequency:       80.0
# Debug Interface:           FPGA JTAG
# ##############################################################################
 PARAMETER VERSION = 2.1.0


# ##############################################################################
# Top Level Ports
# ##############################################################################
 PORT UserIO_LEDs = UserIO_LEDs, DIR = O, VEC = [0:7]
 PORT UserIO_IOEx_SDA = UserIO_IOEx_SDA, DIR = O
 PORT UserIO_IOEx_SCL = UserIO_IOEx_SCL, DIR = O
 PORT UserIO_PB = UserIO_PB, DIR = I, VEC = [0:3]
 PORT UserIO_DIPSW = UserIO_DIPSW, DIR = I, VEC = [0:3]
 PORT rs232_db9_RX = rs232_db9_RX, DIR = I
 PORT rs232_db9_TX = rs232_db9_TX, DIR = O
 PORT rs232_usb_RX = rs232_usb_RX, DIR = I
 PORT rs232_usb_TX = rs232_usb_TX, DIR = O
 PORT ETH_TemacPhy_RST_n = ETH_TemacPhy_RST_n, DIR = O
 PORT ETH_MII_TX_CLK = ETH_MII_TX_CLK, DIR = I
 PORT ETH_GMII_TXD = ETH_GMII_TXD, DIR = O, VEC = [7:0]
 PORT ETH_GMII_TX_EN = ETH_GMII_TX_EN, DIR = O
 PORT ETH_GMII_TX_ER = ETH_GMII_TX_ER, DIR = O
 PORT ETH_GMII_TX_CLK = ETH_GMII_TX_CLK, DIR = O
 PORT ETH_GMII_RXD = ETH_GMII_RXD, DIR = I, VEC = [7:0]
 PORT ETH_GMII_RX_DV = ETH_GMII_RX_DV, DIR = I
 PORT ETH_GMII_RX_ER = ETH_GMII_RX_ER, DIR = I
 PORT ETH_GMII_RX_CLK = ETH_GMII_RX_CLK, DIR = I
 PORT ETH_MDC = ETH_MDC, DIR = O
 PORT ETH_MDIO = ETH_MDIO, DIR = IO
# Clock board config
 PORT clk_board_config_sys_clk = clk_board_config_sys_clk, DIR = I
 PORT clk_board_config_radio_dat_out = clk_board_config_radio_dat_out, DIR = O
 PORT clk_board_config_radio_csb_out = clk_board_config_radio_csb_out, DIR = O
 PORT clk_board_config_radio_en_out = clk_board_config_radio_en_out, DIR = O
 PORT clk_board_config_radio_clk_out = clk_board_config_radio_clk_out, DIR = O
 PORT clk_board_config_logic_dat_out = clk_board_config_logic_dat_out, DIR = O
 PORT clk_board_config_logic_csb_out = clk_board_config_logic_csb_out, DIR = O
 PORT clk_board_config_logic_en_out = clk_board_config_logic_en_out, DIR = O
 PORT clk_board_config_logic_clk_out = clk_board_config_logic_clk_out, DIR = O
# RFA transceiver and front-end (daughtercard slot 2)
 PORT RFA_TxEn = RFA_TxEn, DIR = O
 PORT RFA_RxEn = RFA_RxEn, DIR = O
 PORT RFA_RxHP = RFA_RxHP, DIR = O
 PORT RFA_SHDN = RFA_SHDN, DIR = O
 PORT RFA_SPI_SCLK = RFA_SPI_SCLK, DIR = O
 PORT RFA_SPI_MOSI = RFA_SPI_MOSI, DIR = O
 PORT RFA_SPI_CSn = RFA_SPI_CSn, DIR = O
 PORT RFA_B = RFA_B, DIR = O, VEC = [0:6]
 PORT RFA_LD = RFA_LD, DIR = I
 PORT RFA_PAEn_24 = RFA_PAEn_24, DIR = O
 PORT RFA_PAEn_5 = RFA_PAEn_5, DIR = O
 PORT RFA_AntSw = RFA_AntSw, DIR = O, VEC = [0:1]
# R G Y
 PORT RFA_LEDs = 0b0 & RFA_statLED_Tx & RFA_statLED_Rx, DIR = O, VEC = [0:2]
 PORT RFA_DIPSW = RFA_DIPSW, DIR = I, VEC = [0:3]
# RFB transceiver and front-end (daughtercard slot 3)
 PORT RFB_TxEn = RFB_TxEn, DIR = O
 PORT RFB_RxEn = RFB_RxEn, DIR = O
 PORT RFB_RxHP = RFB_RxHP, DIR = O
 PORT RFB_SHDN = RFB_SHDN, DIR = O
 PORT RFB_SPI_SCLK = RFB_SPI_SCLK, DIR = O
 PORT RFB_SPI_MOSI = RFB_SPI_MOSI, DIR = O
 PORT RFB_SPI_CSn = RFB_SPI_CSn, DIR = O
 PORT RFB_B = RFB_B, DIR = O, VEC = [0:6]
 PORT RFB_LD = RFB_LD, DIR = I
 PORT RFB_PAEn_24 = RFB_PAEn_24, DIR = O
 PORT RFB_PAEn_5 = RFB_PAEn_5, DIR = O
 PORT RFB_AntSw = RFB_AntSw, DIR = O, VEC = [0:1]
 PORT RFB_LEDs = 0b0 & RFB_statLED_Tx & RFB_statLED_Rx, DIR = O, VEC = [0:2]
 PORT RFB_DIPSW = RFB_DIPSW, DIR = I, VEC = [0:3]
# RFC transceiver and front-end (daughtercard slot 1)
 PORT RFC_TxEn = RFC_TxEn, DIR = O
 PORT RFC_RxEn = RFC_RxEn, DIR = O
 PORT RFC_RxHP = RFC_RxHP, DIR = O
 PORT RFC_SHDN = RFC_SHDN, DIR = O
 PORT RFC_SPI_SCLK = RFC_SPI_SCLK, DIR = O
 PORT RFC_SPI_MOSI = RFC_SPI_MOSI, DIR = O
 PORT RFC_SPI_CSn = RFC_SPI_CSn, DIR = O
 PORT RFC_B = RFC_B, DIR = O, VEC = [0:6]
 PORT RFC_LD = RFC_LD, DIR = I
 PORT RFC_PAEn_24 = RFC_PAEn_24, DIR = O
 PORT RFC_PAEn_5 = RFC_PAEn_5, DIR = O
 PORT RFC_AntSw = RFC_AntSw, DIR = O, VEC = [0:1]
 PORT RFC_LEDs = 0b0 & RFC_statLED_Tx & RFC_statLED_Rx, DIR = O, VEC = [0:2]
 PORT RFC_DIPSW = RFC_DIPSW, DIR = I, VEC = [0:3]
# RFD transceiver and front-end (daughtercard slot 4)
 PORT RFD_TxEn = RFD_TxEn, DIR = O
 PORT RFD_RxEn = RFD_RxEn, DIR = O
 PORT RFD_RxHP = RFD_RxHP, DIR = O
 PORT RFD_SHDN = RFD_SHDN, DIR = O
 PORT RFD_SPI_SCLK = RFD_SPI_SCLK, DIR = O
 PORT RFD_SPI_MOSI = RFD_SPI_MOSI, DIR = O
 PORT RFD_SPI_CSn = RFD_SPI_CSn, DIR = O
 PORT RFD_B = RFD_B, DIR = O, VEC = [0:6]
 PORT RFD_LD = RFD_LD, DIR = I
 PORT RFD_PAEn_24 = RFD_PAEn_24, DIR = O
 PORT RFD_PAEn_5 = RFD_PAEn_5, DIR = O
 PORT RFD_AntSw = RFD_AntSw, DIR = O, VEC = [0:1]
 PORT RFD_LEDs = 0b0 & RFD_statLED_Tx & RFD_statLED_Rx, DIR = O, VEC = [0:2]
 PORT RFD_DIPSW = RFD_DIPSW, DIR = I, VEC = [0:3]
# RSSI ADCs
 PORT RFA_RSSI_ADC_D = RFA_RSSI_ADC_D, DIR = I, VEC = [9:0]
 PORT RFA_RSSI_ADC_CLK = RFA_RSSI_ADC_CLK, DIR = O
 PORT RFA_RSSI_ADC_CLAMP = RFA_RSSI_ADC_CLAMP, DIR = O
 PORT RFA_RSSI_ADC_HIZ = RFA_RSSI_ADC_HIZ, DIR = O
 PORT RFA_RSSI_ADC_SLEEP = RFA_RSSI_ADC_SLEEP, DIR = O
 PORT RFB_RSSI_ADC_D = RFB_RSSI_ADC_D, DIR = I, VEC = [9:0]
 PORT RFB_RSSI_ADC_CLK = RFB_RSSI_ADC_CLK, DIR = O
 PORT RFB_RSSI_ADC_CLAMP = RFB_RSSI_ADC_CLAMP, DIR = O
 PORT RFB_RSSI_ADC_HIZ = RFB_RSSI_ADC_HIZ, DIR = O
 PORT RFB_RSSI_ADC_SLEEP = RFB_RSSI_ADC_SLEEP, DIR = O
 PORT RFC_RSSI_ADC_D = RFC_RSSI_ADC_D, DIR = I, VEC = [9:0]
 PORT RFC_RSSI_ADC_CLK = RFC_RSSI_ADC_CLK, DIR = O
 PORT RFC_RSSI_ADC_CLAMP = RFC_RSSI_ADC_CLAMP, DIR = O
 PORT RFC_RSSI_ADC_HIZ = RFC_RSSI_ADC_HIZ, DIR = O
 PORT RFC_RSSI_ADC_SLEEP = RFC_RSSI_ADC_SLEEP, DIR = O
 PORT RFD_RSSI_ADC_D = RFD_RSSI_ADC_D, DIR = I, VEC = [9:0]
 PORT RFD_RSSI_ADC_CLK = RFD_RSSI_ADC_CLK, DIR = O
 PORT RFD_RSSI_ADC_CLAMP = RFD_RSSI_ADC_CLAMP, DIR = O
 PORT RFD_RSSI_ADC_HIZ = RFD_RSSI_ADC_HIZ, DIR = O
 PORT RFD_RSSI_ADC_SLEEP = RFD_RSSI_ADC_SLEEP, DIR = O
# I/Q ADCs/DACs
 PORT RFA_DAC_I = RFA_DAC_I, DIR = O, VEC = [15:0]
 PORT RFA_DAC_Q = RFA_DAC_Q, DIR = O, VEC = [15:0]
 PORT RFA_DAC_SPI_CSn = RFA_DAC_SPI_CSn, DIR = O
 PORT RFA_DAC_SPI_SCLK = RFA_DAC_SPI_SCLK, DIR = O
 PORT RFA_DAC_SPI_MOSI = RFA_DAC_SPI_MOSI, DIR = O
 PORT RFA_DAC_SPI_MISO = RFA_DAC_SPI_MISO, DIR = I
 PORT RFA_DAC_RESET = RFA_DAC_RESET, DIR = O
 PORT RFA_DAC_PLLLOCK = RFA_DAC_PLLLOCK, DIR = I
 PORT RFA_RX_ADC_I = RFA_RX_ADC_I, DIR = I, VEC = [13:0]
 PORT RFA_RX_ADC_Q = RFA_RX_ADC_Q, DIR = I, VEC = [13:0]
 PORT RFA_RX_ADC_I_OTR = RFA_RX_ADC_I_OTR, DIR = I
 PORT RFA_RX_ADC_Q_OTR = RFA_RX_ADC_Q_OTR, DIR = I
 PORT RFA_RX_ADC_DCS = RFA_RX_ADC_DCS, DIR = O
 PORT RFA_RX_ADC_DFS = RFA_RX_ADC_DFS, DIR = O
 PORT RFA_RX_ADC_I_PWDN = RFA_RX_ADC_PWDN, DIR = O
 PORT RFA_RX_ADC_Q_PWDN = RFA_RX_ADC_PWDN, DIR = O
 PORT RFB_DAC_I = RFB_DAC_I, DIR = O, VEC = [15:0]
 PORT RFB_DAC_Q = RFB_DAC_Q, DIR = O, VEC = [15:0]
 PORT RFB_DAC_SPI_CSn = RFB_DAC_SPI_CSn, DIR = O
 PORT RFB_DAC_SPI_SCLK = RFB_DAC_SPI_SCLK, DIR = O
 PORT RFB_DAC_SPI_MOSI = RFB_DAC_SPI_MOSI, DIR = O
 PORT RFB_DAC_SPI_MISO = RFB_DAC_SPI_MISO, DIR = I
 PORT RFB_DAC_RESET = RFB_DAC_RESET, DIR = O
 PORT RFB_DAC_PLLLOCK = RFB_DAC_PLLLOCK, DIR = I
 PORT RFB_RX_ADC_I = RFB_RX_ADC_I, DIR = I, VEC = [13:0]
 PORT RFB_RX_ADC_Q = RFB_RX_ADC_Q, DIR = I, VEC = [13:0]
 PORT RFB_RX_ADC_I_OTR = RFB_RX_ADC_I_OTR, DIR = I
 PORT RFB_RX_ADC_Q_OTR = RFB_RX_ADC_Q_OTR, DIR = I
 PORT RFB_RX_ADC_DCS = RFB_RX_ADC_DCS, DIR = O
 PORT RFB_RX_ADC_DFS = RFB_RX_ADC_DFS, DIR = O
 PORT RFB_RX_ADC_I_PWDN = RFB_RX_ADC_PWDN, DIR = O
 PORT RFB_RX_ADC_Q_PWDN = RFB_RX_ADC_PWDN, DIR = O
 PORT RFC_DAC_I = RFC_DAC_I, DIR = O, VEC = [15:0]
 PORT RFC_DAC_Q = RFC_DAC_Q, DIR = O, VEC = [15:0]
 PORT RFC_DAC_SPI_CSn = RFC_DAC_SPI_CSn, DIR = O
 PORT RFC_DAC_SPI_SCLK = RFC_DAC_SPI_SCLK, DIR = O
 PORT RFC_DAC_SPI_MOSI = RFC_DAC_SPI_MOSI, DIR = O
 PORT RFC_DAC_SPI_MISO = RFC_DAC_SPI_MISO, DIR = I
 PORT RFC_DAC_RESET = RFC_DAC_RESET, DIR = O
 PORT RFC_DAC_PLLLOCK = RFC_DAC_PLLLOCK, DIR = I
 PORT RFC_RX_ADC_I = RFC_RX_ADC_I, DIR = I, VEC = [13:0]
 PORT RFC_RX_ADC_Q = RFC_RX_ADC_Q, DIR = I, VEC = [13:0]
 PORT RFC_RX_ADC_I_OTR = RFC_RX_ADC_I_OTR, DIR = I
 PORT RFC_RX_ADC_Q_OTR = RFC_RX_ADC_Q_OTR, DIR = I
 PORT RFC_RX_ADC_DCS = RFC_RX_ADC_DCS, DIR = O
 PORT RFC_RX_ADC_DFS = RFC_RX_ADC_DFS, DIR = O
 PORT RFC_RX_ADC_I_PWDN = RFC_RX_ADC_PWDN, DIR = O
 PORT RFC_RX_ADC_Q_PWDN = RFC_RX_ADC_PWDN, DIR = O
 PORT RFD_DAC_I = RFD_DAC_I, DIR = O, VEC = [15:0]
 PORT RFD_DAC_Q = RFD_DAC_Q, DIR = O, VEC = [15:0]
 PORT RFD_DAC_SPI_CSn = RFD_DAC_SPI_CSn, DIR = O
 PORT RFD_DAC_SPI_SCLK = RFD_DAC_SPI_SCLK, DIR = O
 PORT RFD_DAC_SPI_MOSI = RFD_DAC_SPI_MOSI, DIR = O
 PORT RFD_DAC_SPI_MISO = RFD_DAC_SPI_MISO, DIR = I
 PORT RFD_DAC_RESET = RFD_DAC_RESET, DIR = O
 PORT RFD_DAC_PLLLOCK = RFD_DAC_PLLLOCK, DIR = I
 PORT RFD_RX_ADC_I = RFD_RX_ADC_I, DIR = I, VEC = [13:0]
 PORT RFD_RX_ADC_Q = RFD_RX_ADC_Q, DIR = I, VEC = [13:0]
 PORT RFD_RX_ADC_I_OTR = RFD_RX_ADC_I_OTR, DIR = I
 PORT RFD_RX_ADC_Q_OTR = RFD_RX_ADC_Q_OTR, DIR = I
 PORT RFD_RX_ADC_DCS = RFD_RX_ADC_DCS, DIR = O
 PORT RFD_RX_ADC_DFS = RFD_RX_ADC_DFS, DIR = O
 PORT RFD_RX_ADC_I_PWDN = RFD_RX_ADC_PWDN, DIR = O
 PORT RFD_RX_ADC_Q_PWDN = RFD_RX_ADC_PWDN, DIR = O
# EEPROM I/O
 PORT RFA_EEPROM_IO = RFA_EEPROM_IO, DIR = IO
 PORT RFB_EEPROM_IO = RFB_EEPROM_IO, DIR = IO
 PORT RFC_EEPROM_IO = RFC_EEPROM_IO, DIR = IO
 PORT RFD_EEPROM_IO = RFD_EEPROM_IO, DIR = IO
 PORT FPGA_EEPROM_IO = FPGA_EEPROM_IO, DIR = IO
# Clock & Reset
 PORT clk_1_sys_clk = CLK_S, DIR = I, SIGIS = CLK, CLK_FREQ = 40000000
 PORT rst_1_sys_rst = sys_rst_s, DIR = I, SIGIS = RST, RST_POLARITY = 1
# Digital I/O header
 PORT debughdr = debug_capture_running & debug_transmit_running, DIR = O, VEC = [1:0]
 PORT debug_sw_gpio = debug_sw_gpio, DIR = IO, VEC = [1:0]
 PORT trigger_in = trig_0_in & trig_1_in & trig_2_in & trig_3_in, DIR = I, VEC = [0:3]
 PORT trigger_0_out = trig_2_0_out & trig_3_0_out & trig_4_0_out & trig_5_0_out, DIR = O, VEC = [0:3]
 PORT trigger_1_out = trig_2_1_out & trig_3_1_out & trig_4_1_out & trig_5_1_out, DIR = O, VEC = [0:3]


# Optional Debug Header functionality
# To switch to 6 SW GPIO pins on the Debug Header:
# - Change above debug_sw_gpio line to:
# PORT debug_sw_gpio = debug_sw_gpio, DIR = IO, VEC = [5:0]
# - Modify the xps_gpio instance and change C_GPIO_WIDTH to 6 GPIOs
# - Comment out trigger_1_out
# - Modify the system.ucf file to use the debug_sw_gpio pins instead of the trigger_1_out pins
# ##############################################################################
# Processor
# ##############################################################################
BEGIN ppc405_virtex4
 PARAMETER INSTANCE = ppc405_0
 PARAMETER C_FASTEST_PLB_CLOCK = DPLB0
 PARAMETER C_IDCR_BASEADDR = 0b0100000000
 PARAMETER C_IDCR_HIGHADDR = 0b0111111111
 PARAMETER HW_VER = 2.01.b
 BUS_INTERFACE DPLB0 = plb
 BUS_INTERFACE IPLB0 = plb
 BUS_INTERFACE DSOCM = ppc405_0_docm
 BUS_INTERFACE ISOCM = ppc405_0_iocm
 BUS_INTERFACE JTAGPPC = ppc405_0_jtagppc_bus
 BUS_INTERFACE RESETPPC = ppc_reset_bus
 PORT CPMC405CLOCK = clk_160_0000MHzDCM0
END

BEGIN isocm_v10
 PARAMETER INSTANCE = ppc405_0_iocm
 PARAMETER C_ISCNTLVALUE = 0xa3
 PARAMETER HW_VER = 2.00.b
 PORT ISOCM_Clk = clk_80_0000MHzDCM0
 PORT SYS_Rst = sys_bus_reset
END

BEGIN isbram_if_cntlr
 PARAMETER INSTANCE = ppc405_0_iocm_cntlr
 PARAMETER HW_VER = 3.00.c
 PARAMETER C_BASEADDR = 0xffff0000
 PARAMETER C_HIGHADDR = 0xffffffff
 BUS_INTERFACE ISOCM = ppc405_0_iocm
 BUS_INTERFACE DCR_WRITE_PORT = ppc405_0_iocm_cntlr_porta
 BUS_INTERFACE INSTRN_READ_PORT = ppc405_0_iocm_cntlr_portb
END

BEGIN bram_block
 PARAMETER INSTANCE = ppc405_0_iocm_cntlr_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = ppc405_0_iocm_cntlr_porta
 BUS_INTERFACE PORTB = ppc405_0_iocm_cntlr_portb
END

BEGIN dsocm_v10
 PARAMETER INSTANCE = ppc405_0_docm
 PARAMETER C_DSCNTLVALUE = 0xa3
 PARAMETER HW_VER = 2.00.b
 PORT DSOCM_Clk = clk_80_0000MHzDCM0
 PORT SYS_Rst = sys_bus_reset
END

BEGIN dsbram_if_cntlr
 PARAMETER INSTANCE = ppc405_0_docm_cntlr
 PARAMETER HW_VER = 3.00.c
 PARAMETER C_BASEADDR = 0x40110000
 PARAMETER C_HIGHADDR = 0x4011ffff
 BUS_INTERFACE DSOCM = ppc405_0_docm
 BUS_INTERFACE PORTA = ppc405_0_docm_cntlr_porta
END

BEGIN bram_block
 PARAMETER INSTANCE = ppc405_0_docm_cntlr_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = ppc405_0_docm_cntlr_porta
END

# ##############################################################################
# Clock / Reset / Debug
# ##############################################################################
BEGIN clock_generator
 PARAMETER INSTANCE = clock_generator_0
 PARAMETER C_CLKIN_FREQ = 40000000
 PARAMETER C_CLKOUT0_FREQ = 125000000
 PARAMETER C_CLKOUT0_PHASE = 0
 PARAMETER C_CLKOUT0_GROUP = NONE
 PARAMETER C_CLKOUT0_BUF = TRUE
 PARAMETER C_CLKOUT1_FREQ = 160000000
 PARAMETER C_CLKOUT1_PHASE = 0
 PARAMETER C_CLKOUT1_GROUP = DCM0
 PARAMETER C_CLKOUT1_BUF = TRUE
 PARAMETER C_CLKOUT2_FREQ = 200000000
 PARAMETER C_CLKOUT2_PHASE = 0
 PARAMETER C_CLKOUT2_GROUP = NONE
 PARAMETER C_CLKOUT2_BUF = TRUE
 PARAMETER C_CLKOUT3_FREQ = 40000000
 PARAMETER C_CLKOUT3_PHASE = 0
 PARAMETER C_CLKOUT3_GROUP = NONE
 PARAMETER C_CLKOUT3_BUF = TRUE
 PARAMETER C_CLKOUT4_FREQ = 80000000
 PARAMETER C_CLKOUT4_PHASE = 0
 PARAMETER C_CLKOUT4_GROUP = DCM0
 PARAMETER C_CLKOUT4_BUF = TRUE
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER HW_VER = 4.03.a
 PORT CLKIN = CLK_S
 PORT CLKOUT0 = clk_125_0000MHz
 PORT CLKOUT1 = clk_160_0000MHzDCM0
 PORT CLKOUT2 = clk_200_0000MHz
 PORT CLKOUT3 = clk_40_0000MHz
 PORT CLKOUT4 = clk_80_0000MHzDCM0
 PORT RST = clk_board_config_config_invalid
 PORT LOCKED = Dcm_all_locked
END

BEGIN jtagppc_cntlr
 PARAMETER INSTANCE = jtagppc_cntlr_inst
 PARAMETER HW_VER = 2.01.c
 BUS_INTERFACE JTAGPPC0 = ppc405_0_jtagppc_bus
END

BEGIN proc_sys_reset
 PARAMETER INSTANCE = proc_sys_reset_0
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER HW_VER = 3.00.a
 BUS_INTERFACE RESETPPC0 = ppc_reset_bus
 PORT Slowest_sync_clk = clk_40_0000MHz
 PORT Ext_Reset_In = sys_rst_s
 PORT Dcm_locked = Dcm_all_locked
 PORT Bus_Struct_Reset = sys_bus_reset
 PORT Peripheral_Reset = sys_periph_reset
END

# ##############################################################################
# Interconnect
# ##############################################################################
BEGIN plb_v46
 PARAMETER INSTANCE = plb
 PARAMETER C_DCR_INTFCE = 0
 PARAMETER C_NUM_CLK_PLB2OPB_REARB = 100
 PARAMETER HW_VER = 1.05.a
 PORT PLB_Clk = clk_80_0000MHzDCM0
 PORT SYS_Rst = sys_bus_reset
END

# ##############################################################################
# Peripherals
# ##############################################################################
BEGIN xps_central_dma
 PARAMETER INSTANCE = xps_central_dma_0
 PARAMETER HW_VER = 2.03.a
 PARAMETER C_BASEADDR = 0x81000000
 PARAMETER C_HIGHADDR = 0x8100FFFF
 BUS_INTERFACE MPLB = plb
 BUS_INTERFACE SPLB = plb
END

BEGIN xps_timer
 PARAMETER INSTANCE = xps_timer_0
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BASEADDR = 0x80100000
 PARAMETER C_HIGHADDR = 0x8010FFFF
 BUS_INTERFACE SPLB = plb
END

BEGIN xps_gpio
 PARAMETER INSTANCE = xps_gpio_0
 PARAMETER HW_VER = 2.00.a
# PARAMETER C_GPIO_WIDTH = 6
 PARAMETER C_GPIO_WIDTH = 2
 PARAMETER C_BASEADDR = 0x80000000
 PARAMETER C_HIGHADDR = 0x8000FFFF
 BUS_INTERFACE SPLB = plb
 PORT GPIO_IO_O = debug_sw_gpio
END

BEGIN xps_uartlite
 PARAMETER INSTANCE = rs232_db9
 PARAMETER C_BAUDRATE = 57600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_ODD_PARITY = 0
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BASEADDR = 0x80300000
 PARAMETER C_HIGHADDR = 0x8030FFFF
 BUS_INTERFACE SPLB = plb
 PORT RX = rs232_db9_RX
 PORT TX = rs232_db9_TX
END

BEGIN xps_uartlite
 PARAMETER INSTANCE = rs232_usb
 PARAMETER C_BAUDRATE = 57600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_ODD_PARITY = 0
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BASEADDR = 0x80200000
 PARAMETER C_HIGHADDR = 0x8020FFFF
 BUS_INTERFACE SPLB = plb
 PORT RX = rs232_usb_RX
 PORT TX = rs232_usb_TX
END

BEGIN xps_bram_if_cntlr
 PARAMETER INSTANCE = xps_bram_if_cntlr_1
 PARAMETER C_SPLB_NATIVE_DWIDTH = 64
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0000ffff
 BUS_INTERFACE SPLB = plb
 BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
END

BEGIN bram_block
 PARAMETER INSTANCE = plb_bram_if_cntlr_1_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
END

# ##############################################################################
# Ethernet
# ##############################################################################
BEGIN xps_ll_temac
 PARAMETER INSTANCE = ETH_A_MAC
 PARAMETER C_NUM_IDELAYCTRL = 2
 PARAMETER C_IDELAYCTRL_LOC = IDELAYCTRL_X1Y5-IDELAYCTRL_X1Y6
 PARAMETER C_PHY_TYPE = 1
 PARAMETER C_BUS2CORE_CLK_RATIO = 1
 PARAMETER C_TEMAC_TYPE = 1
 PARAMETER HW_VER = 2.03.a
 PARAMETER C_BASEADDR = 0x82100000
 PARAMETER C_HIGHADDR = 0x8217FFFF
 PARAMETER C_TEMAC0_TXFIFO = 2048
 PARAMETER C_TEMAC0_RXFIFO = 2048
 PARAMETER C_TEMAC0_TXCSUM = 0
 PARAMETER C_TEMAC0_RXCSUM = 0
 BUS_INTERFACE SPLB = plb
 BUS_INTERFACE LLINK0 = ETH_llink0
 PORT TemacPhy_RST_n = ETH_TemacPhy_RST_n
 PORT GTX_CLK_0 = clk_125_0000MHz
 PORT REFCLK = clk_200_0000MHz
 PORT LlinkTemac0_CLK = clk_80_0000MHzDCM0
 PORT MII_TX_CLK_0 = ETH_MII_TX_CLK
 PORT GMII_TXD_0 = ETH_GMII_TXD
 PORT GMII_TX_EN_0 = ETH_GMII_TX_EN
 PORT GMII_TX_ER_0 = ETH_GMII_TX_ER
 PORT GMII_TX_CLK_0 = ETH_GMII_TX_CLK
 PORT GMII_RXD_0 = ETH_GMII_RXD
 PORT GMII_RX_DV_0 = ETH_GMII_RX_DV
 PORT GMII_RX_ER_0 = ETH_GMII_RX_ER
 PORT GMII_RX_CLK_0 = ETH_GMII_RX_CLK
 PORT MDC_0 = ETH_MDC
 PORT MDIO_0 = ETH_MDIO
END

BEGIN xps_ll_fifo
 PARAMETER INSTANCE = ETH_A_FIFO
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BASEADDR = 0x82000000
 PARAMETER C_HIGHADDR = 0x8200FFFF
 BUS_INTERFACE SPLB = plb
 BUS_INTERFACE LLINK = ETH_llink0
END

# ##############################################################################
# Mango Cores
# ##############################################################################
BEGIN warp_v4_userio
 PARAMETER INSTANCE = UserIO
 PARAMETER C_ADDRESS_0 = 0x40
 PARAMETER C_ADDRESS_1 = 0x42
 PARAMETER C_I2C_DIVIDER = 0x40
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_BASEADDR = 0x80500000
 PARAMETER C_HIGHADDR = 0x8050FFFF
 BUS_INTERFACE SPLB = plb
 PORT LEDs_out = UserIO_LEDs
 PORT IOEx_SDA = UserIO_IOEx_SDA
 PORT IOEx_SCL = UserIO_IOEx_SCL
 PORT PB_in = UserIO_PB
 PORT DIPSW_in = UserIO_DIPSW
END

BEGIN clock_board_config
 PARAMETER INSTANCE = clk_board_config
 PARAMETER HW_VER = 1.05.a
 PARAMETER radio_clk_out4_mode = 0x1eff
 PARAMETER radio_clk_out7_mode = 0x1eff
 PARAMETER logic_clk_out0_mode = 0x08ff
 PARAMETER logic_clk_out1_mode = 0x08ff
 PARAMETER radio_clk_source_sel_mode = 1
 PARAMETER logic_clk_source_sel_mode = 1
 PARAMETER fpga_radio_clk_source = 1
 PARAMETER fpga_logic_clk_source = 1
 PARAMETER radio_clk_forward_out_mode = 0x08FF
 PARAMETER logic_clk_forward_out_mode = 0x1EFF
 PORT sys_clk = clk_board_config_sys_clk
 PORT sys_rst = net_gnd
 PORT cfg_radio_dat_out = clk_board_config_radio_dat_out
 PORT cfg_radio_csb_out = clk_board_config_radio_csb_out
 PORT cfg_radio_en_out = clk_board_config_radio_en_out
 PORT cfg_radio_clk_out = clk_board_config_radio_clk_out
 PORT cfg_logic_dat_out = clk_board_config_logic_dat_out
 PORT cfg_logic_csb_out = clk_board_config_logic_csb_out
 PORT cfg_logic_en_out = clk_board_config_logic_en_out
 PORT cfg_logic_clk_out = clk_board_config_logic_clk_out
 PORT radio_clk_src_sel = radio2_dipsw_zero
 PORT logic_clk_src_sel = radio2_dipsw_one
 PORT config_invalid = clk_board_config_config_invalid
END

BEGIN util_bus_split
 PARAMETER INSTANCE = util_bus_split_0
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_SIZE_IN = 4
 PARAMETER C_SPLIT = 2
 PORT Sig = RFA_DIPSW
 PORT Out1 = radio2_dipsw_zero & radio2_dipsw_one
END

BEGIN eeprom_onewire
 PARAMETER INSTANCE = eeprom_controller
 PARAMETER HW_VER = 1.10.a
 PARAMETER C_MEM0_BASEADDR = 0x80400000
 PARAMETER C_MEM0_HIGHADDR = 0x8040FFFF
 BUS_INTERFACE SPLB = plb
 PORT DQ0 = FPGA_EEPROM_IO
 PORT DQ1 = RFA_EEPROM_IO
 PORT DQ2 = RFB_EEPROM_IO
 PORT DQ3 = RFC_EEPROM_IO
 PORT DQ4 = RFD_EEPROM_IO
 PORT DQ5_I = net_vcc
 PORT DQ6_I = net_vcc
 PORT DQ7_I = net_vcc
END

BEGIN radio_controller
 PARAMETER INSTANCE = radio_controller_0
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_BASEADDR = 0x85000000
 PARAMETER C_HIGHADDR = 0x8500FFFF
 BUS_INTERFACE SPLB = plb
# RFA
 PORT RFA_TxEn = RFA_TxEn
 PORT RFA_RxEn = RFA_RxEn
 PORT RFA_RxHP = RFA_RxHP
 PORT RFA_SHDN = RFA_SHDN
 PORT RFA_SPI_SCLK = RFA_SPI_SCLK
 PORT RFA_SPI_MOSI = RFA_SPI_MOSI
 PORT RFA_SPI_CSn = RFA_SPI_CSn
 PORT RFA_B = RFA_B
 PORT RFA_LD = RFA_LD
 PORT RFA_PAEn_24 = RFA_PAEn_24
 PORT RFA_PAEn_5 = RFA_PAEn_5
 PORT RFA_AntSw = RFA_AntSw
 PORT RFA_DIPSW = RFA_DIPSW
 PORT RFA_RSSI_ADC_CLAMP = RFA_RSSI_ADC_CLAMP
 PORT RFA_RSSI_ADC_HIZ = RFA_RSSI_ADC_HIZ
 PORT RFA_RSSI_ADC_SLEEP = RFA_RSSI_ADC_SLEEP
 PORT RFA_DAC_SPI_CSn = RFA_DAC_SPI_CSn
 PORT RFA_DAC_SPI_SCLK = RFA_DAC_SPI_SCLK
 PORT RFA_DAC_SPI_MOSI = RFA_DAC_SPI_MOSI
 PORT RFA_DAC_SPI_MISO = RFA_DAC_SPI_MISO
 PORT RFA_DAC_RESET = RFA_DAC_RESET
 PORT RFA_DAC_PLLLOCK = RFA_DAC_PLLLOCK
 PORT RFA_RX_ADC_DCS = RFA_RX_ADC_DCS
 PORT RFA_RX_ADC_DFS = RFA_RX_ADC_DFS
 PORT RFA_RX_ADC_PWDN = RFA_RX_ADC_PWDN
# RFA - User ports
 PORT usr_RFA_statLED_Tx = RFA_statLED_Tx
 PORT usr_RFA_statLED_Rx = RFA_statLED_Rx
 PORT usr_RFA_RxHP = agc_rxhp_a
 PORT usr_RFA_RxGainRF = agc_g_rf_a
 PORT usr_RFA_RxGainBB = agc_g_bb_a
# RFB
 PORT RFB_TxEn = RFB_TxEn
 PORT RFB_RxEn = RFB_RxEn
 PORT RFB_RxHP = RFB_RxHP
 PORT RFB_SHDN = RFB_SHDN
 PORT RFB_SPI_SCLK = RFB_SPI_SCLK
 PORT RFB_SPI_MOSI = RFB_SPI_MOSI
 PORT RFB_SPI_CSn = RFB_SPI_CSn
 PORT RFB_B = RFB_B
 PORT RFB_LD = RFB_LD
 PORT RFB_PAEn_24 = RFB_PAEn_24
 PORT RFB_PAEn_5 = RFB_PAEn_5
 PORT RFB_AntSw = RFB_AntSw
 PORT RFB_DIPSW = RFB_DIPSW
 PORT RFB_RSSI_ADC_CLAMP = RFB_RSSI_ADC_CLAMP
 PORT RFB_RSSI_ADC_HIZ = RFB_RSSI_ADC_HIZ
 PORT RFB_RSSI_ADC_SLEEP = RFB_RSSI_ADC_SLEEP
 PORT RFB_DAC_SPI_CSn = RFB_DAC_SPI_CSn
 PORT RFB_DAC_SPI_SCLK = RFB_DAC_SPI_SCLK
 PORT RFB_DAC_SPI_MOSI = RFB_DAC_SPI_MOSI
 PORT RFB_DAC_SPI_MISO = RFB_DAC_SPI_MISO
 PORT RFB_DAC_RESET = RFB_DAC_RESET
 PORT RFB_DAC_PLLLOCK = RFB_DAC_PLLLOCK
 PORT RFB_RX_ADC_DCS = RFB_RX_ADC_DCS
 PORT RFB_RX_ADC_DFS = RFB_RX_ADC_DFS
 PORT RFB_RX_ADC_PWDN = RFB_RX_ADC_PWDN
# RFB - User ports
 PORT usr_RFB_statLED_Tx = RFB_statLED_Tx
 PORT usr_RFB_statLED_Rx = RFB_statLED_Rx
 PORT usr_RFB_RxHP = agc_rxhp_b
 PORT usr_RFB_RxGainRF = agc_g_rf_b
 PORT usr_RFB_RxGainBB = agc_g_bb_b
# RFC
 PORT RFC_TxEn = RFC_TxEn
 PORT RFC_RxEn = RFC_RxEn
 PORT RFC_RxHP = RFC_RxHP
 PORT RFC_SHDN = RFC_SHDN
 PORT RFC_SPI_SCLK = RFC_SPI_SCLK
 PORT RFC_SPI_MOSI = RFC_SPI_MOSI
 PORT RFC_SPI_CSn = RFC_SPI_CSn
 PORT RFC_B = RFC_B
 PORT RFC_LD = RFC_LD
 PORT RFC_PAEn_24 = RFC_PAEn_24
 PORT RFC_PAEn_5 = RFC_PAEn_5
 PORT RFC_AntSw = RFC_AntSw
 PORT RFC_DIPSW = RFC_DIPSW
 PORT RFC_RSSI_ADC_CLAMP = RFC_RSSI_ADC_CLAMP
 PORT RFC_RSSI_ADC_HIZ = RFC_RSSI_ADC_HIZ
 PORT RFC_RSSI_ADC_SLEEP = RFC_RSSI_ADC_SLEEP
 PORT RFC_DAC_SPI_CSn = RFC_DAC_SPI_CSn
 PORT RFC_DAC_SPI_SCLK = RFC_DAC_SPI_SCLK
 PORT RFC_DAC_SPI_MOSI = RFC_DAC_SPI_MOSI
 PORT RFC_DAC_SPI_MISO = RFC_DAC_SPI_MISO
 PORT RFC_DAC_RESET = RFC_DAC_RESET
 PORT RFC_DAC_PLLLOCK = RFC_DAC_PLLLOCK
 PORT RFC_RX_ADC_DCS = RFC_RX_ADC_DCS
 PORT RFC_RX_ADC_DFS = RFC_RX_ADC_DFS
 PORT RFC_RX_ADC_PWDN = RFC_RX_ADC_PWDN
# RFC - User ports
 PORT usr_RFC_statLED_Tx = RFC_statLED_Tx
 PORT usr_RFC_statLED_Rx = RFC_statLED_Rx
 PORT usr_RFC_RxHP = agc_rxhp_c
 PORT usr_RFC_RxGainRF = agc_g_rf_c
 PORT usr_RFC_RxGainBB = agc_g_bb_c
# RFD
 PORT RFD_TxEn = RFD_TxEn
 PORT RFD_RxEn = RFD_RxEn
 PORT RFD_RxHP = RFD_RxHP
 PORT RFD_SHDN = RFD_SHDN
 PORT RFD_SPI_SCLK = RFD_SPI_SCLK
 PORT RFD_SPI_MOSI = RFD_SPI_MOSI
 PORT RFD_SPI_CSn = RFD_SPI_CSn
 PORT RFD_B = RFD_B
 PORT RFD_LD = RFD_LD
 PORT RFD_PAEn_24 = RFD_PAEn_24
 PORT RFD_PAEn_5 = RFD_PAEn_5
 PORT RFD_AntSw = RFD_AntSw
 PORT RFD_DIPSW = RFD_DIPSW
 PORT RFD_RSSI_ADC_CLAMP = RFD_RSSI_ADC_CLAMP
 PORT RFD_RSSI_ADC_HIZ = RFD_RSSI_ADC_HIZ
 PORT RFD_RSSI_ADC_SLEEP = RFD_RSSI_ADC_SLEEP
 PORT RFD_DAC_SPI_CSn = RFD_DAC_SPI_CSn
 PORT RFD_DAC_SPI_SCLK = RFD_DAC_SPI_SCLK
 PORT RFD_DAC_SPI_MOSI = RFD_DAC_SPI_MOSI
 PORT RFD_DAC_SPI_MISO = RFD_DAC_SPI_MISO
 PORT RFD_DAC_RESET = RFD_DAC_RESET
 PORT RFD_DAC_PLLLOCK = RFD_DAC_PLLLOCK
 PORT RFD_RX_ADC_DCS = RFD_RX_ADC_DCS
 PORT RFD_RX_ADC_DFS = RFD_RX_ADC_DFS
 PORT RFD_RX_ADC_PWDN = RFD_RX_ADC_PWDN
# RFD - User ports
 PORT usr_RFD_statLED_Tx = RFD_statLED_Tx
 PORT usr_RFD_statLED_Rx = RFD_statLED_Rx
 PORT usr_RFD_RxHP = agc_rxhp_d
 PORT usr_RFD_RxGainRF = agc_g_rf_d
 PORT usr_RFD_RxGainBB = agc_g_bb_d
END

BEGIN radio_bridge
 PARAMETER INSTANCE = radio_bridge_RFA
 PARAMETER HW_VER = 2.00.a
 PORT samp_clock = clk_40_0000MHz
 PORT radio_ADC_I = RFA_RX_ADC_I
 PORT radio_ADC_Q = RFA_RX_ADC_Q
 PORT radio_DAC_I = RFA_DAC_I
 PORT radio_DAC_Q = RFA_DAC_Q
 PORT radio_ADC_I_OTR = RFA_RX_ADC_I_OTR
 PORT radio_ADC_Q_OTR = RFA_RX_ADC_Q_OTR
 PORT user_ADC_I = warplab_rfa_Rx_I
 PORT user_ADC_Q = warplab_rfa_Rx_Q
 PORT user_DAC_I = warplab_rfa_Tx_I
 PORT user_DAC_Q = warplab_rfa_Tx_Q
 PORT radio_RSSI_ADC_D = RFA_RSSI_ADC_D
 PORT radio_RSSI_ADC_CLK = RFA_RSSI_ADC_CLK
 PORT user_RSSI_ADC_D = warplab_rfa_rssi
 PORT user_RSSI_ADC_CLK = warplab_rssi_clk
END

BEGIN radio_bridge
 PARAMETER INSTANCE = radio_bridge_RFB
 PARAMETER HW_VER = 2.00.a
 PORT samp_clock = clk_40_0000MHz
 PORT radio_ADC_I = RFB_RX_ADC_I
 PORT radio_ADC_Q = RFB_RX_ADC_Q
 PORT radio_DAC_I = RFB_DAC_I
 PORT radio_DAC_Q = RFB_DAC_Q
 PORT radio_ADC_I_OTR = RFB_RX_ADC_I_OTR
 PORT radio_ADC_Q_OTR = RFB_RX_ADC_Q_OTR
 PORT user_ADC_I = warplab_rfb_Rx_I
 PORT user_ADC_Q = warplab_rfb_Rx_Q
 PORT user_DAC_I = warplab_rfb_Tx_I
 PORT user_DAC_Q = warplab_rfb_Tx_Q
 PORT radio_RSSI_ADC_D = RFB_RSSI_ADC_D
 PORT radio_RSSI_ADC_CLK = RFB_RSSI_ADC_CLK
 PORT user_RSSI_ADC_D = warplab_rfb_rssi
 PORT user_RSSI_ADC_CLK = warplab_rssi_clk
END

BEGIN radio_bridge
 PARAMETER INSTANCE = radio_bridge_RFC
 PARAMETER HW_VER = 2.00.a
 PORT samp_clock = clk_40_0000MHz
 PORT radio_ADC_I = RFC_RX_ADC_I
 PORT radio_ADC_Q = RFC_RX_ADC_Q
 PORT radio_DAC_I = RFC_DAC_I
 PORT radio_DAC_Q = RFC_DAC_Q
 PORT radio_ADC_I_OTR = RFC_RX_ADC_I_OTR
 PORT radio_ADC_Q_OTR = RFC_RX_ADC_Q_OTR
 PORT user_ADC_I = warplab_rfc_Rx_I
 PORT user_ADC_Q = warplab_rfc_Rx_Q
 PORT user_DAC_I = warplab_rfc_Tx_I
 PORT user_DAC_Q = warplab_rfc_Tx_Q
 PORT radio_RSSI_ADC_D = RFC_RSSI_ADC_D
 PORT radio_RSSI_ADC_CLK = RFC_RSSI_ADC_CLK
 PORT user_RSSI_ADC_D = warplab_rfc_rssi
 PORT user_RSSI_ADC_CLK = warplab_rssi_clk
END

BEGIN radio_bridge
 PARAMETER INSTANCE = radio_bridge_RFD
 PARAMETER HW_VER = 2.00.a
 PORT samp_clock = clk_40_0000MHz
 PORT radio_ADC_I = RFD_RX_ADC_I
 PORT radio_ADC_Q = RFD_RX_ADC_Q
 PORT radio_DAC_I = RFD_DAC_I
 PORT radio_DAC_Q = RFD_DAC_Q
 PORT radio_ADC_I_OTR = RFD_RX_ADC_I_OTR
 PORT radio_ADC_Q_OTR = RFD_RX_ADC_Q_OTR
 PORT user_ADC_I = warplab_rfd_Rx_I
 PORT user_ADC_Q = warplab_rfd_Rx_Q
 PORT user_DAC_I = warplab_rfd_Tx_I
 PORT user_DAC_Q = warplab_rfd_Tx_Q
 PORT radio_RSSI_ADC_D = RFD_RSSI_ADC_D
 PORT radio_RSSI_ADC_CLK = RFD_RSSI_ADC_CLK
 PORT user_RSSI_ADC_D = warplab_rfd_rssi
 PORT user_RSSI_ADC_CLK = warplab_rssi_clk
END

# ##############################################################################
# Local Cores
# ##############################################################################
BEGIN w2_warplab_trigger_proc_plbw
 PARAMETER INSTANCE = warplab_trigger_proc
 PARAMETER HW_VER = 1.04.b
 PARAMETER C_BASEADDR = 0x84000000
 PARAMETER C_HIGHADDR = 0x8400FFFF
 BUS_INTERFACE SPLB = plb
 PORT sysgen_clk = clk_160_0000MHzDCM0
 PORT agc_done_in = agc_is_done
 PORT rfa_rssi = warplab_rfa_rssi
 PORT rfb_rssi = warplab_rfb_rssi
 PORT rfc_rssi = warplab_rfc_rssi
 PORT rfd_rssi = warplab_rfd_rssi
 PORT rssi_clk = warplab_rssi_clk
# Debug header trigger inputs
 PORT debug_0_in = trig_0_in
 PORT debug_1_in = trig_1_in
 PORT debug_2_in = trig_2_in
 PORT debug_3_in = trig_3_in
# Trigger outputs to internal modules
 PORT trig_0_out = baseband_trigger
 PORT trig_1_out = agc_start
# Trigger outputs to the debug header
 PORT trig_2_0_out = trig_2_0_out
 PORT trig_3_0_out = trig_3_0_out
 PORT trig_4_0_out = trig_4_0_out
 PORT trig_5_0_out = trig_5_0_out
# Replicated trigger outputs to the debug header
 PORT trig_2_1_out = trig_2_1_out
 PORT trig_3_1_out = trig_3_1_out
 PORT trig_4_1_out = trig_4_1_out
 PORT trig_5_1_out = trig_5_1_out
END

BEGIN w2_warplab_buffers_plbw
 PARAMETER INSTANCE = warplab_buffers
 PARAMETER HW_VER = 3.01.c
 PARAMETER C_BASEADDR = 0x83000000
 PARAMETER C_HIGHADDR = 0x833FFFFF
 BUS_INTERFACE SPLB = plb
 PORT sysgen_clk = clk_40_0000MHz
 PORT rssi_adc_clk = warplab_rssi_clk
 PORT DESIGN_VER = 0x00070501
 PORT agc_done = agc_is_done
# RFA
 PORT rfa_dac_i = warplab_rfa_Tx_I
 PORT rfa_dac_q = warplab_rfa_Tx_Q
 PORT rfa_adc_i = warplab_rfa_Rx_I
 PORT rfa_adc_q = warplab_rfa_Rx_Q
 PORT rfa_agc_filt_i = dc_filtered_i_a
 PORT rfa_agc_filt_q = dc_filtered_q_a
 PORT rfa_rssi = warplab_rfa_rssi
 PORT rfa_g_bb = agc_g_bb_a
 PORT rfa_g_rf = agc_g_rf_a
 PORT rfa_rxhp = agc_rxhp_a
# RFB
 PORT rfb_dac_i = warplab_rfb_Tx_I
 PORT rfb_dac_q = warplab_rfb_Tx_Q
 PORT rfb_adc_i = warplab_rfb_Rx_I
 PORT rfb_adc_q = warplab_rfb_Rx_Q
 PORT rfb_agc_filt_i = dc_filtered_i_b
 PORT rfb_agc_filt_q = dc_filtered_q_b
 PORT rfb_rssi = warplab_rfb_rssi
 PORT rfb_g_bb = agc_g_bb_b
 PORT rfb_g_rf = agc_g_rf_b
 PORT rfb_rxhp = agc_rxhp_b
# RFC
 PORT rfc_dac_i = warplab_rfc_Tx_I
 PORT rfc_dac_q = warplab_rfc_Tx_Q
 PORT rfc_adc_i = warplab_rfc_Rx_I
 PORT rfc_adc_q = warplab_rfc_Rx_Q
 PORT rfc_agc_filt_i = dc_filtered_i_c
 PORT rfc_agc_filt_q = dc_filtered_q_c
 PORT rfc_rssi = warplab_rfc_rssi
 PORT rfc_g_bb = agc_g_bb_c
 PORT rfc_g_rf = agc_g_rf_c
 PORT rfc_rxhp = agc_rxhp_c
# RFD
 PORT rfd_dac_i = warplab_rfd_Tx_I
 PORT rfd_dac_q = warplab_rfd_Tx_Q
 PORT rfd_adc_i = warplab_rfd_Rx_I
 PORT rfd_adc_q = warplab_rfd_Rx_Q
 PORT rfd_agc_filt_i = dc_filtered_i_d
 PORT rfd_agc_filt_q = dc_filtered_q_d
 PORT rfd_rssi = warplab_rfd_rssi
 PORT rfd_g_bb = agc_g_bb_d
 PORT rfd_g_rf = agc_g_rf_d
 PORT rfd_rxhp = agc_rxhp_d
# Other ports
 PORT stoptx = net_gnd
 PORT trigger_in = baseband_trigger
 PORT capture_running = debug_capture_running
 PORT transmit_running = debug_transmit_running
 PORT dram_init_done = net_gnd
END

BEGIN w2_warplab_agc_plbw
 PARAMETER INSTANCE = warplab_agc
 PARAMETER HW_VER = 3.00.b
 PARAMETER C_BASEADDR = 0x84800000
 PARAMETER C_HIGHADDR = 0x8480FFFF
 BUS_INTERFACE SPLB = plb
 PORT sysgen_clk = clk_80_0000MHzDCM0
 PORT adc_rx_clk = clk_40_0000MHz
 PORT agc_run = agc_start
 PORT agc_done = agc_is_done
# RFA
 PORT rfa_agc_rxhp = agc_rxhp_a
 PORT rfa_agc_g_bb = agc_g_bb_a
 PORT rfa_agc_g_rf = agc_g_rf_a
 PORT rfa_rssi = warplab_rfa_rssi
 PORT rfa_rx_i_in = warplab_rfa_Rx_I
 PORT rfa_rx_q_in = warplab_rfa_Rx_Q
 PORT rfa_rx_i_out = dc_filtered_i_a
 PORT rfa_rx_q_out = dc_filtered_q_a
# RFB
 PORT rfb_agc_rxhp = agc_rxhp_b
 PORT rfb_agc_g_bb = agc_g_bb_b
 PORT rfb_agc_g_rf = agc_g_rf_b
 PORT rfb_rssi = warplab_rfb_rssi
 PORT rfb_rx_i_in = warplab_rfb_Rx_I
 PORT rfb_rx_q_in = warplab_rfb_Rx_Q
 PORT rfb_rx_i_out = dc_filtered_i_b
 PORT rfb_rx_q_out = dc_filtered_q_b
# RFC
 PORT rfc_agc_rxhp = agc_rxhp_c
 PORT rfc_agc_g_bb = agc_g_bb_c
 PORT rfc_agc_g_rf = agc_g_rf_c
 PORT rfc_rssi = warplab_rfc_rssi
 PORT rfc_rx_i_in = warplab_rfc_Rx_I
 PORT rfc_rx_q_in = warplab_rfc_Rx_Q
 PORT rfc_rx_i_out = dc_filtered_i_c
 PORT rfc_rx_q_out = dc_filtered_q_c
# RFD
 PORT rfd_agc_rxhp = agc_rxhp_d
 PORT rfd_agc_g_bb = agc_g_bb_d
 PORT rfd_agc_g_rf = agc_g_rf_d
 PORT rfd_rssi = warplab_rfd_rssi
 PORT rfd_rx_i_in = warplab_rfd_Rx_I
 PORT rfd_rx_q_in = warplab_rfd_Rx_Q
 PORT rfd_rx_i_out = dc_filtered_i_d
 PORT rfd_rx_q_out = dc_filtered_q_d
END