Version 14 (modified by murphpo, 17 years ago) (diff) |
---|
MIMO OFDM? | Documentation? | OFDM Model Register Map
Register bits [31:16]
Register bits [15:0]
Rx_ControlBits
Address: 0x0
Dir: Read/Write
Fields:
CFO_USE_LONGCORR
(Bit 12) Enables the use of the long correlator to control the timing of the carrier frequency offset estimation based on the long training symbols. This must be set to 1 for normal operation.
CFO_USE_STS
(Bit 11) Enables carrier frequency offset estimation based on the preamble's short training symbols. When using high-quality oscillators, this can be disabled to improve CFO estimation performance.
CFO_USE_LTS
(Bit 10) Enables carrier frequency offset estimation based on the preamble's long training symbols. Must be set to 1 for normal operation.
CFO_BYPASS
(Bit 9) When set to 1, CFO correction is bypassed. This should only be used when driving two nodes from a common reference clock during PHY debugging.
INT_PKTDET_EN
(Bit 8) Enables the internal packet detection block. This should only be used when debugging the PHY over a wire when the external packet detector is not being used.
EXT_PKTDET_EN
(Bit 7) Enables external packet detection via the rx_extpktdet top-level port
REQ_SHORT_CORR
(Bit 6) Requires either internal or external packet detection in order to begin processing a packet. When disabled, the receiver will begin processing packets when trigged only by the long correlator.
REQ_TWO_LONG_CORR
(Bit 5) Requires two threshold crossings from the long correlator, spaced exactly 64 cycles apart. When enaled, this makes packet detection more robust at the cost of more false negative detections.
SISO_MODE
(Bit 4) Enables single-antenna (SISO) mode in the receiver. In this mode, only packets transmitted in SISO mode will be properly received.
DYN_PKT_LENGTHS
(Bit 2) Enables dynamic packet lengths. This should be 1 for normal operation. When disabled, the receiver assumes every packet is a fixed length. This is useful during PHY debugging and BER testing.
REQ_LONG_CORR
(Bit 1) Requires a threshold crossing in the long correlator for packet detection. This must be one for reliable operation.
BER_RESET
(Bit 0) When enabled, the BER calculation engine is held in reset. This should be 0 only during BER testing.
Rx_GlobalReset
Address: 0x4
Dir: Read/Write
Fields:
RX_RESET
(Bit 0) Global reset for the receiver state machines. When set to 1, all state in the packet detection, PHY processing, packet construction and interrupt blocks is cleared. This reset does not clear the values of OPB regsters.
Rx_OFDM_SymbolCounts
Address: 0x8
Dir: Read/Write
Fields:
NUM_BASERATE_SYMS
(Bits 31:16 - UFix16_0) This integer sets the number of base rate symbols the receiver should process with each incoming packet. See the OFDM frame format documentation for more information.
NUM_TRAINING_SYMS
(Bits 15:0 - UFix16_0) This integer sets the number of training symbol periods at the receiver. This value corresponds to the number of OFDM symbol periods dedicated to training. In MIMO mode, the training symbols are divided between antennas, orthogally in time. In SISO mode, every training period is used for estimating the single channel. See the OFDM frame format documentation for more information.
Rx_PktDet_Delay
Address: 0xC
Dir: Read/Write
Fields:
PKT_DET_DELAY
(Bits 6:0 - UFix7_0) This integer sets the delay inserted between the course packet detection signal and the start of receiver processing. This delay should correspond to the time difference between packet detection and the start of the preamble's fourth short training symbol.
Rx_PktDet_LongCorr_Params
Address: 0x10
Dir: Read/Write
Fields:
CORR_SET_TIMING
(Bits 31:16 - UFix16_0) This integer sets sample index used when a long correlation event occurs. The receiver uses a large counter to track packet timing. This counter increments with each sample, starting with course packet detection. When the long correlator crosses its threshold, the counter is set to this value.
CORR_THRESHOLD
(Bits 15:0 - UFix16_0) This integer sets the long correlation threshold used during fine packet detection and symbol timing.
Rx_PktDone_Reset
Address: 0x14
Dir: Read/Write
Fields:
EN_BADPKT_INT
(Bit 5) Enables the bad packet interrupt output. The interrupt is raised via the top-level output rx_int_badpkt. Bad packets are defined as packets which fail the CRC checksum calculation.
EN_GOODPKT_INT
(Bit 4) Enables the good packet interrupt output. The interrupt is raised via the top-level output rx_int_goodpkt. Good packets are defined as packets which pass the CRC checksum calculation.
RST_BADPKT_INT
(Bit 1) Resets the bad packet interrupt. The application must assert & de-assert this bit after processing a bad packet.
RST_GOODPKT_INT
(Bit 0) Resets the good packet interrupt. The application must assert & de-assert this bit after processing a good packet.
Rx_symbolTimingOffset
Address: 0x18
Dir: Read/Write
Fields:
SYMBOL_TIMING_OFFSET
(Bits 5:0 - UFix6_0) This integer sets the nominal symbol timing offset. This value is used as the starting index for the FFT calculation of each received OFDM symbol. This value must be less than the cyclic prefix length.
Rx_FreqOffFilt_KI
Address: 0x1C
Dir: Read/Write
Fields:
CFO_FILT_COEF_I
(Bits 31:0 - UFix32_32) Integral path coefficient for the loop filter in the carrier frequency offset pilot phase tracking system.
Rx_FreqOffFilt_KP
Address: 0x20
Dir: Read/Write
Fields:
CFO_FILT_COEF_P
(Bits 31:0 - UFix32_32) Proportional path coefficient for the loop filter in the carrier frequency offset pilot phase tracking system.
Rx_Constellation_Scaling
Address: 0x24
Dir: Read/Write
Fields:
ANT_B_SCALING
(Bits 31:16 - UFix16_11) This fixed-point value is used to scale the output of the equalizer for antenna B before symbols are detected. This scaling is used to fit the received constellation to the pre-defined hard decision boundaries used during symbol detection.
ANT_A_SCALING
(Bits 15:0 - UFix16_11) This fixed-point value is used to scale the output of the equalizer for antenna A before symbols are detected. This scaling is used to fit the received constellation to the pre-defined hard decision boundaries used during symbol detection.
Rx_FFT_Scaling
Address: 0x28
Dir: Read/Write
Fields:
RX_FFT_SCALING_0
(Bits 5:4 - UFix2_0) This integer sets the scaling after the first stage of the FFT calculation.
RX_FFT_SCALING_1
(Bits 3:2 - UFix2_0) This integer sets the scaling after the middle stage of the FFT calculation.
RX_FFT_SCALING_2
(Bits 1:0 - UFix2_0) This integer sets the scaling after the last stage of the FFT calculation.
Rx_pktDet_Corr_Thresh
Address: 0x2C
Dir: Read/Write
Fields:
PKTDET_CORR_THRESH
(Bits 7:0 - UFix8_7) This fixed-point value is the correlation threshold used for the internal packetion system.
Rx_pktDet_Energy_Thresh
Address: 0x30
Dir: Read/Write
Fields:
PKTDET_ENERGY_THRESH
(Bits 11:0 - UFix12_5) This fixed-point value is the energy threshold used for the internal packetion system.
Tx_FFT_Scaling
Address: 0x34
Dir: Read/Write
Fields:
TX_FFT_SCALING_0
(Bits 5:4 - UFix2_0) This integer sets the scaling after the first stage of the IFFT calculation.
TX_FFT_SCALING_1
(Bits 3:2 - UFix2_0) This integer sets the scaling after the middle stage of the IFFT calculation.
TX_FFT_SCALING_2
(Bits 1:0 - UFix2_0) This integer sets the scaling after the last stage of the IFFT calculation.
Tx_PreambleScaling
Address: 0x38
Dir: Read/Write
Fields:
PREAMBLE_SCALING
(Bits 15:0 - UFix16_16) This fraction sets the scaling of the preamble. The preamble is stored with a full-scale swing on [-1, +1]. The actual transmitted preamble is scaled by this fration.
Tx_NumPayloadBytes
Address: 0x3C
Dir: Read/Write
Fields:
NUM_BYTES
(Bits 11:0 - UFix12_0) This integer is the number of payload bytes present in the packet being prepared for transmission. This value must be updated before the transmitter is started. The application must assure that this value agrees with NUM_PYLD_SYMS and the selected modulation scheme.
Tx_RandomPayload_ModSel
Address: 0x40
Dir: Read/Write
Fields:
RAND_PLD_MOD_SEL
(Bits 1:0 - UFix2_0) This integer selects the modulation scheme used when random payload mode in the transmitter is enabled. The mapping is [0,1,2,3] = [0, QPSK, 16-QAM, 64-QAM].
Tx_Pilots_Index1
Address: 0x44
Dir: Read/Write
Fields:
PILOT1_INDEX_1
(Bits 5:0 - UFix6_0) Subcarrier index for first copy of pilot tone 1. This index should be symmetric about DC with PILOT1_INDEX_2 below.
PILOT1_INDEX_2
(Bits 21:16 - UFix6_0) Subcarrier index for second copy of pilot tone 1. This index should be symmetric about DC with PILOT1_INDEX_1 above.
Tx_Pilots_Index2
Address: 0x48
Dir: Read/Write
Fields:
PILOT2_INDEX_1
(Bits 5:0 - UFix6_0) Subcarrier index for first copy of pilot tone 2. This index should be symmetric about DC with PILOT2_INDEX_2 below.
PILOT2_INDEX_2
(Bits 21:16 - UFix6_0) Subcarrier index for second copy of pilot tone 2. This index should be symmetric about DC with PILOT2_INDEX_1 above.
Tx_Pilots_Value1
Address: 0x4C
Dir: Read/Write
Fields:
PILOT1_ANTA_VALUE
(Bits 15:0 - Fix16_15) Value for pilot tone 1 on antenna A.
PILOT1_ANTB_VALUE
(Bits 31:16 - Fix16_15) Value for pilot tone 1 on antenna B.
Tx_Pilots_Value2
Address: 0x50
Dir: Read/Write
Fields:
PILOT2_ANTA_VALUE
(Bits 15:0 - Fix16_15) Value for pilot tone 2 on antenna A.
PILOT2_ANTB_VALUE
(Bits 31:16 - Fix16_15) Value for pilot tone 2 on antenna B.
Tx_OFDM_SymCounts
Address: 0x54
Dir: Read/Write
Fields:
NUM_TRAINING_SYMS
(Bits 7:0 - UFix8_0) Number of training symbols transmitted before the payload in each packet. This value can be changed per packet, but must remain constant during a transmission.
NUM_BASERATE_SYMS
(Bits 15:8 - UFix8_0) Number of base rate symbols sent per packet. A base rate symbol is modulated at a different rate than the full rate symbols which follow. Also, identical base rate symbols are sent from both antennas; true multiplexing only applies to full rate symbols.
NUM_PYLD_SYMS
(Bits 31:16 - UFix16_0) Number of full rate OFDM symbols in the transmitted packet. Full rate symbols are modulated at a faster rate and are sent multiplexed across both antennas. This number must be even when MIMO mode is enabled. The transmitter will pad the payload to fill unoccupied space in full OFDM symbols.
Tx_Start_Reset_Control
Address: 0x58
Dir: Read/Write
Fields:
TX_RESET
(Bits 1:0 - UFix1_0) Global active-high reset for the transmitter subsystem. When asserted, all internal state in the transmitter will be cleared, except the register bank.
TX_START
(Bits 2:1 - UFix1_0) Trigger for beginning a packet transmission. This register bit acts exactly like the tx_starttransmit input port. Only one trigger option (port or register) should be used per packet.
TX_PKTDONE_RESET
(Bits 3:2 - UFix1_0) Clears the state of the Tx_PktDone register. User code should toggle this register high/low after each packet transmission.
Tx_ControlBits
Address: 0x5C
Dir: Read/Write
Fields:
SISO_MODE
(Bits 1:0 - UFix1_0) Enables SISO mode in the transmitter. This option can be enabled per packet and will only function correctly when used with a receiver in SISO mode.
RANDOM_PYLD
(Bits 2:1 - UFix1_0) Enables random payload mode, which transmits random symbols in every subcarrier. The modulation scheme used is configured in the RAND_PLD_MOD_SEL field.
DISABLE_ANTB_PREAMBLE
(Bits 3:2 - UFix1_0) When asserted, disables the transmission of a preamble from antenna B.
EN_PILOT_SCRAMBLING
(Bits 4:3 - UFix1_0) Enables 802.11-style pilot tone scrambling. When used, pseudo-random sign changes will be applied per OFDM symbol.
Rx_BER_Errors
Address: 0x60
Dir: Read-only
Fields:
BER_ERRORS
(Bits 31:0 - UFix32_0) Total number of bit errors detected. BER measurements are only useful when the default packet is repeatedly transmitted.
Rx_BER_TotalBits
Address: 0x64
Dir: Read-only
Fields:
BER_TOTALBITS
(Bits 31:0 - UFix32_0) Total number of bits received. Divide BER_ERRORS by this field to calculate the bit error rate.
Rx_packet_done
Address: 0x68
Dir: Read-only
Fields:
RX_GOODPKT
(Bits 1:0 - UFix1_0) Active high when a good packet is received. This field will only go high when EN_GOODPKT_INT is enabled and must be cleared by asserting RST_GOODPKT_INT.
RX_BADPKT
(Bits 2:1 - UFix1_0) Active high when a bad packet is received. This field will only go high when EN_BADPKT_INT is enabled and must be cleared by asserting RST_BADPKT_INT.
Tx_PktDone
Address: 0x6C
Dir: Read-only
TX_PKT_DONE
(Bits 1:0 - UFix1_0) Active high when a packet transmission is complete. This field can be cleared by toggling TX_PKTDONE_RESET.